ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Repair of Laminations in 16MnReR Low-Temperature Pressure Vessel Steel by Surfacing

Background and Significance

This paper from 1990 describes a repair campaign on four 1000 m³ spherical tanks fabricated from domestic 16MnReR low-temperature pressure vessel steel. The tanks, with a diameter of 12.3 m and a design working pressure of 1.57 MPa, were erected in 1984 for a plant in Shenyang. During radiographic and ultrasonic examination, one tank revealed laminar discontinuities in the base metal near the weld seam that exceeded the acceptance criteria. This is a serious finding because laminations in low-temperature service steel can act as initiation sites for brittle fracture, especially when combined with the high restraint of a spherical shell and the presence of welding residual stress. The paper's contribution lies in demonstrating a practical repair route using E1507FcNi electrodes, a nickel-bearing low-hydrogen electrode designed for low-temperature service, and in validating the repair by subsequent non-destructive examination. For an industry veteran, this case is a textbook example of how to handle a non-conforming condition in a critical pressure vessel without scrapping the entire unit, which would have been an enormous commercial and schedule loss.

Metallurgical Considerations for the Repair

The base material 16MnReR is a manganese-silicon steel with rare earth additions, specified for service down to approximately -40 °C. The presence of laminations in the near-weld zone is a plate quality issue, not a welding defect, and it arises from non-metallic inclusions or segregation bands in the original plate rolling process. The repair method chosen, surfacing (or buttering) the affected area, works by depositing a sound layer of weld metal over the lamination, effectively sealing the discontinuity from the service environment and providing a continuous load path. The critical metallurgical challenge is to avoid introducing new defects, particularly hydrogen-induced cracking in the heat-affected zone of the base metal. The use of E1507FcNi, which is a low-hydrogen electrode with nickel additions, is a wise choice because nickel improves the toughness of the weld metal at low temperatures and the low-hydrogen coating minimises the risk of delayed cracking. The preheat and interpass temperature control, while not detailed in the abstract, would have been essential for a 16MnReR steel of this thickness, typically in the range of 40 to 60 mm for a 1000 m³ sphere.

Repair Procedure and Quality Control

The repair sequence follows a logical path that any experienced welding engineer would recognise. First, the lamination is located precisely by ultrasonic testing and its extent is mapped. Then the area is prepared by grinding or gouging to sound metal, ensuring the lamination is fully exposed and the cavity has a geometry that allows proper weld access. The surfacing is then deposited in multiple passes, with the first layer acting as a buttering layer to minimise dilution with the base metal and to establish a sound interface. The subsequent layers build up the required thickness, and the final surface is machined or ground flush. The critical quality control steps are the intermediate and final non-destructive examination. Radiographic testing would be used to verify the absence of lack of fusion or slag inclusions in the repair, while ultrasonic testing would confirm the lamination has been fully covered and that no new planar discontinuities have been introduced. The paper's success is evidenced by the fact that the tank was returned to service, but a veteran would also insist on a hydrostatic test of the sphere after the repair, which is a mandatory requirement for pressure vessels in this service class.

Practical Lessons from the Shop Floor

This case reinforces several hard-won lessons. First, plate quality is a procurement issue, and the cost of a lamination discovered after fabrication is far higher than the cost of rejecting the plate at the mill. A thorough ultrasonic examination of the plate before forming and welding is a cheap insurance policy. Second, repair welding on low-temperature steel demands strict adherence to the welding procedure specification, particularly regarding preheat, interpass temperature, and post-weld heat treatment if required. Third, the choice of a nickel-bearing electrode for the repair is a sound metallurgical decision, but it also requires careful control of the heat input to avoid excessive grain growth in the HAZ. Finally, the documentation of the repair, including the exact location, extent, and repair procedure, is essential for the integrity management of the vessel over its service life. In my experience, a repair that is properly executed and documented can restore a vessel to full serviceability, but a repair that is rushed or poorly controlled can create a new defect that is worse than the original.

Summary

This paper provides a valuable case study in the repair of laminations in low-temperature pressure vessel steel, demonstrating that a well-planned surfacing procedure using a nickel-bearing low-hydrogen electrode can successfully restore a spherical tank to service. The key technical points are the selection of the correct electrode, strict control of preheat and interpass temperature, and comprehensive non-destructive examination before and after the repair. For engineers facing similar issues, this case underscores the importance of plate quality control, the metallurgical rationale behind the repair method, and the need for rigorous quality assurance throughout the repair process. The lessons learned here are timeless and apply directly to modern pressure vessel fabrication, where laminations in low-temperature steel remain a real risk.