Plasma Arc Surfacing of ZGMn13 High Manganese Steel
Literature Overview and Context
The paper by Zhang Fucheng, published in Hot Working Technology in 1998, presents an experimental study on the plasma arc surfacing of ZGMn13 high manganese steel. The author is affiliated with Yanshan University, a leading institution in materials science and engineering in China. The paper investigates the feasibility of using plasma arc welding (PAW) with a filler wire to deposit a hardfacing layer on ZGMn13 steel.
ZGMn13 is a high manganese steel, also known as Hadfield steel, which is widely used in applications requiring high impact resistance and work-hardening capability, such as railway crossings, crusher jaws, and excavator buckets. The steel is austenitic and has a unique property: it work-hardens under impact, becoming harder and more wear-resistant at the surface while maintaining a tough core.
However, welding ZGMn13 is notoriously difficult. The heat-affected zone (HAZ) is prone to carbide precipitation at the grain boundaries, which leads to a loss of toughness and makes the material susceptible to cracking. The paper's focus on plasma arc surfacing is significant because this process offers a lower heat input than conventional arc welding processes, which can help mitigate the carbide precipitation problem.
Core Technical Points and Process Interpretation
The core of this paper is the metallurgical analysis of the weld zone and the HAZ after plasma arc surfacing. The author likely used optical microscopy and mechanical testing to evaluate the quality of the deposit and the integrity of the HAZ.
The key finding, as stated in the abstract, is that the plasma arc surfacing process results in a HAZ that is free of carbide precipitation and grain growth. This is a significant result because it indicates that the low heat input of the plasma arc process is sufficient to prevent the formation of carbides, which are the primary cause of embrittlement in welded ZGMn13.
| Parameter | Plasma Arc Surfacing | Conventional GMAW |
|---|---|---|
| Heat Input | 0.5-1.5 kJ/mm | 1.5-3.0 kJ/mm |
| HAZ Width | Narrow (1-2 mm) | Wide (3-5 mm) |
| Carbide Precipitation | None observed | Likely to occur |
| Grain Growth | Minimal | Significant |
| Dilution Rate | Low (5-10%) | Moderate (10-20%) |
The plasma arc process uses a constricted arc that is transferred to the workpiece. The constriction results in a high energy density and a narrow heat-affected zone. The filler wire is fed into the plasma arc, where it is melted and deposited onto the workpiece. The process is typically used with a transferred arc, which provides good penetration and a high deposition rate.
The paper likely also discusses the selection of the filler wire. For surfacing ZGMn13, the filler wire should be similar in composition to the base material to maintain the austenitic structure and the work-hardening properties. However, the filler wire may also contain alloying elements such as chromium or nickel to improve the corrosion resistance or the hardness of the deposit.
Practical Lessons and Engineering Insights
The successful application of plasma arc surfacing to ZGMn13 has significant implications for the repair and manufacture of wear-resistant components. The ability to weld ZGMn13 without causing carbide precipitation means that components can be repaired and returned to service, rather than being replaced.
One of the key lessons from this work is the importance of controlling the heat input. In plasma arc welding, the heat input is controlled by the welding current, the arc voltage, the travel speed, and the plasma gas flow rate. The author likely optimized these parameters to achieve a heat input that is low enough to prevent carbide precipitation but high enough to ensure good fusion and a sound deposit.
| Defect | Cause | Countermeasure |
|---|---|---|
| Carbide Precipitation | High heat input | Reduce current or increase travel speed. |
| Cracking | Thermal stress | Preheat or use a low-hydrogen process. |
| Porosity | Contamination or gas entrapment | Clean the surface and ensure proper shielding. |
| Lack of Fusion | Low heat input | Increase current or reduce travel speed. |
Another lesson is the importance of the filler wire composition. The deposit must have the same work-hardening characteristics as the base material. If the filler wire is too hard, the deposit may crack under impact. If it is too soft, the deposit will not provide the required wear resistance.
Study Insights and Implications for the Industry
The paper by Zhang Fucheng is a valuable reference for anyone involved in the welding of high manganese steel. It demonstrates that plasma arc surfacing is a viable method for depositing a hardfacing layer on ZGMn13 without causing the metallurgical problems associated with conventional welding processes.
For fellow engineers, the takeaway is that the choice of welding process can have a significant impact on the metallurgical quality of the weld. Plasma arc welding offers a unique combination of low heat input and high energy density, which makes it particularly suitable for materials that are sensitive to heat input.
In my view, this paper is a good example of the importance of process selection in welding engineering. It also highlights the need for a thorough understanding of the metallurgy of the base material and the effects of the welding thermal cycle. The findings of this paper have practical implications for the repair of railway crossings, crusher components, and other high manganese steel parts.
Zhuojin Pipe Fitting Co., Ltd