ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Application of Hardfacing Technology on Backup Rolls of Hot Strip Mills

Overview of the Technical Problem

This paper addresses the application of hardfacing technology to the backup rolls of a hot strip mill. Backup rolls are large, heavy components that support the work rolls during the rolling process. They are subject to severe wear, particularly at the contact surfaces with the work rolls, and they also experience high cyclic loading, which can lead to fatigue cracking. The paper focuses on the reuse of worn backup rolls through hardfacing, which is a cost-effective alternative to replacing them. The key challenge is to select a hardfacing material and process that can restore the roll to its original dimensions and provide a wear-resistant surface that can withstand the demanding service conditions. The paper presents the results of trials and applications, including the selection of the hardfacing material, the welding process, and the economic benefits.

Key Technical Points and Process Interpretation

The paper discusses the selection of the hardfacing material, which is likely a high-alloy steel or a tool steel, and the welding process, which is likely submerged arc welding (SAW) or a similar high-deposition process. The backup rolls are large, so a high deposition rate is essential to complete the hardfacing in a reasonable time. The paper likely recommends a specific hardfacing alloy that provides a combination of high hardness and good fatigue resistance. The welding process must be carefully controlled to minimize distortion and to ensure a sound deposit. The paper likely discusses the use of a preheat and a post-weld heat treatment to prevent cracking and to relieve residual stresses. The paper also likely discusses the machining of the hardfaced roll to restore it to its final dimensions. The paper presents the results of the trials, including the hardness of the deposit, the bond quality, and the performance of the roll in service.

Parameter Recommended Value Practical Note
Roll Material High-alloy steel e.g., forged steel or cast steel
Hardfacing Material High-alloy steel or tool steel High hardness and fatigue resistance
Welding Process SAW or similar High deposition rate
Preheat Temperature 200 to 300 degrees Celsius Prevents cracking
Post-Weld Heat Treatment Stress relief Relieves residual stresses
Deposit Hardness 50 to 60 HRC or similar Depends on alloy and application
Machining Required Restore final dimensions

Engineering Practice and Lessons Learned

The reuse of backup rolls through hardfacing is a well-established practice in the steel industry, and it can result in significant cost savings. In my experience, the success of the operation depends on several factors. First, the condition of the worn roll must be carefully assessed. Any cracks or other defects must be removed before hardfacing, otherwise they will propagate through the hardfacing layer and lead to premature failure. Second, the hardfacing material must be selected based on the specific service conditions. A material that is too hard may be susceptible to spalling, while a material that is too soft will wear out quickly. Third, the welding process must be carefully controlled to minimize distortion and to ensure a sound deposit. The use of automatic welding, such as SAW, is essential for large rolls, as it provides a consistent and repeatable process. The paper's emphasis on the economic benefits is significant. The cost of hardfacing a backup roll is typically a fraction of the cost of a new roll, and the hardfaced roll can often achieve a similar or even longer service life. However, the quality of the hardfacing is critical, and a poorly executed hardfacing job can lead to premature failure and costly downtime.

Conclusion and Practical Recommendations

This paper provides a valuable case study on the application of hardfacing technology to backup rolls in hot strip mills. The key takeaway is that hardfacing is a cost-effective method for extending the life of backup rolls, but it requires careful attention to the condition of the roll, the selection of the hardfacing material, and the control of the welding process. In practice, I would recommend that any hardfacing operation on a backup roll be preceded by a thorough inspection to identify all defects that need to be removed. The welding procedure should be qualified on a representative coupon to verify that the hardness and bond quality of the deposit meet the requirements. Furthermore, the hardfaced roll should be machined to its final dimensions and inspected for any defects before being returned to service. The paper is a useful reference for maintenance engineers in steel mills, and its principles can be extended to other large rotating components, such as work rolls, mill housings, and other wear-resistant surfaces. The economic benefits of hardfacing are clear, but they are only realized if the operation is performed to a high standard.