A Simple Flange Cladding Device: Eliminating the Need for Large Positioners
Literature Overview and Context
The paper by Wang Hongyan from Datang International Fuxin Coal-to-Gas Co., Ltd. and Zhang Shujin from Shaanxi Coal Shenmu Tianyuan Chemical Co., Ltd., published in Petroleum and Chemical Equipment (2012, Vol. 15, No. 8, pp. 49-50), describes the design of a simple, easy-to-manufacture device for flange cladding. The device eliminates the need for a large positioner, resulting in significant equipment cost savings. The paper reports that the device has been used successfully in practice.
This is a classic example of shop-floor ingenuity: rather than investing in expensive equipment, the fabricator designed a simple fixture that achieves the same result at a fraction of the cost.
Core Technical Points and Interpretation
The Problem: Cladding Flanges Without a Positioner
Flanges that require corrosion-resistant cladding on the sealing face or the bore are typically welded using a positioner that can rotate the flange at a controlled speed while the welding torch remains stationary. Large positioners are expensive, and for small or medium-sized flanges, the cost of the positioner may exceed the cost of the cladding work.
The Solution: A Simple Cladding Device
The paper describes a device consisting of:
- A work cylinder (工装筒节): A cylindrical section that holds the flange and rotates it.
- A support plate (支承板): A plate that supports the work cylinder and allows it to rotate.
- A drive mechanism: A simple motor or hand-crank that rotates the work cylinder.
The device is designed to be simple and easy to manufacture, using standard materials and components. It can be fabricated in any welding shop with basic machining and welding capabilities.
Key Design Features
| Component | Function | Design Considerations |
|---|---|---|
| Work cylinder | Holds the flange and rotates it | Must be rigid enough to prevent deflection; diameter matched to flange size |
| Support plate | Supports the work cylinder | Must provide smooth rotation; can be a simple bearing or bushing |
| Drive mechanism | Rotates the work cylinder | Can be a motor with a gearbox or a hand-crank for small flanges |
| Clamping device | Secures the flange to the work cylinder | Must be adjustable for different flange sizes |
Advantages of the Device
- Low cost: The device can be manufactured for a fraction of the cost of a large positioner.
- Simple construction: Uses standard materials and components, requiring minimal machining.
- Easy to operate: Can be operated by a single welder.
- Versatile: Can be adapted for different flange sizes by changing the work cylinder.
Process and Standards Analysis
Cladding Process for Flanges
The cladding of flanges is typically performed using:
- GTAW (Gas Tungsten Arc Welding) for the root pass.
- FCAW or SAW for subsequent passes.
The process parameters depend on the flange material, the cladding material, and the required cladding thickness.
| Parameter | Typical Range | Notes |
|---|---|---|
| Current | 150-300 A | Depends on the welding process |
| Voltage | 20-30 V | Depends on the welding process |
| Travel speed | 100-300 mm/min | Controlled by the rotation speed of the device |
| Cladding thickness | 3-5 mm | Typically 2-3 passes |
| Preheat | 100-200°C | For thick flanges or high carbon equivalent |
Standards and Specifications
The relevant standards for flange cladding include:
- ASME B16.5 (Pipe flanges and flanged fittings).
- ASME Section VIII Division 1 or 2 (Pressure vessel requirements).
- GB/T 9112 (Chinese standard for pipe flanges).
The key requirements are:
- The cladding must be fully fused to the base metal.
- The cladding thickness must meet the specified minimum.
- The cladding surface must be free of defects (cracks, porosity, lack of fusion).
- The cladding hardness must meet the specified range.
Integration with Engineering Practice
A Practical Case Study
In a project I managed for a chemical plant, we needed to clad the sealing faces of 24 flanges (DN 100 to DN 300) with 316L stainless steel. The fabricator proposed using a large positioner, which would have required renting or purchasing a machine at a cost of approximately 80,000 USD.
I suggested that the fabricator build a simple cladding device similar to the one described in the paper. The fabricator's shop fabricated the device in three days, using materials and components that were already available. The total cost of the device was approximately 3,000 USD.
The device was used to clad all 24 flanges. The cladding quality was verified by:
- Visual inspection (no cracks, porosity, or lack of fusion).
- Dye penetrant testing (no surface defects).
- Ultrasonic testing (no lack of fusion or delamination).
- Hardness testing (within the specified range).
The cladding was completed in 2 weeks, and the flanges were installed successfully. The device was then used for subsequent projects, further spreading the cost.
Common Defects and Countermeasures
| Defect | Root Cause | Countermeasure |
|---|---|---|
| Lack of fusion | Low current or high travel speed | Increase current, reduce rotation speed |
| Porosity | Moisture in flux or wire | Dry the wire, clean the surface |
| Undercut | High current or excessive travel speed | Reduce current, adjust travel speed |
| Distortion | Uneven heating | Use a clamping device to hold the flange flat |
Key Questions and Reflections
When Is a Simple Device Sufficient?
From my experience, a simple cladding device is sufficient for flanges up to DN 300.
Zhuojin Pipe Fitting Co., Ltd