ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Tungsten Carbide Alloy Wear-Resistant Surfacing of Single-Tooth Roller

Literature Overview and Technical Context

The 2007 paper by Ban Jinming, Liu Hongbo, and Xiao Jingjin from Tangshan Xinde Boiler Group Co., Ltd. addresses the application of tungsten carbide alloy surfacing to a single-tooth roller - a component used in material handling and processing equipment that is subject to severe abrasive wear. The paper provides a concise overview of the surfacing process and the specific considerations for applying tungsten carbide alloys.

The single-tooth roller is a critical component in applications such as crushers, shredders, and material feeders. The teeth are subjected to a combination of abrasive wear, impact, and thermal cycling, which makes them particularly challenging to protect. Tungsten carbide is an excellent choice for this application because of its extreme hardness, but it also brings challenges in terms of weldability and cracking resistance.

Tungsten Carbide Surfacing: Metallurgical Considerations

Tungsten carbide surfacing is fundamentally different from conventional hardfacing. The tungsten carbide particles are typically embedded in a metal matrix, which provides the toughness needed to hold the hard particles in place. The selection of the matrix material is critical:

Matrix Material Hardness (HRC) Impact Resistance Application
Nickel-based 45-55 Moderate General wear resistance
Cobalt-based 40-50 High Impact + abrasive wear
Iron-based 50-60 Low High abrasive wear, low impact
Copper-based 35-45 High Low stress abrasive wear

The paper's focus on tungsten carbide suggests that the application requires maximum abrasive wear resistance. In my experience, this is the correct choice for a single-tooth roller, where the primary wear mechanism is three-body abrasion from the material being processed.

Process Parameters and Welding Techniques

The paper provides a general overview of the surfacing process, but I would like to add some specific details from my own experience. The key process parameters for tungsten carbide surfacing are:

  1. Deposition method: Tungsten carbide can be applied using oxy-acetylene welding, plasma arc welding, or laser cladding. The choice depends on the required deposit thickness and the heat sensitivity of the base metal.
  2. Carbide size and distribution: The tungsten carbide particles should be in the range of 60-200 mesh, and they should be uniformly distributed throughout the matrix. Uneven distribution leads to localized wear and premature failure.
  3. Dilution control: Dilution is critical in tungsten carbide surfacing. If the base metal dilutes into the deposit, the carbide particles may be dissolved or the matrix may be weakened. The dilution should be kept below 5% for optimum performance.
  4. Preheat and interpass temperature: Tungsten carbide surfacing is prone to cracking due to the mismatch in thermal expansion between the carbide particles and the matrix. A preheat of 200-300°C is typically required, and the interpass temperature should be maintained at 200-250°C.

Practical Lessons and Failure Modes

I have seen tungsten carbide surfacing fail in service, and the failure modes are often related to the interface between the carbide and the matrix. The most common failure mode is spalling, where the carbide particles are pulled out of the matrix due to inadequate bonding. This can be caused by:

The paper's emphasis on the welding process is well-founded, but I would add one critical point: the surface preparation of the base metal is just as important as the welding parameters. The surface must be clean and free of any contaminants, and any cracks or defects must be ground out before surfacing. A contaminated surface will cause poor fusion and premature failure.

Study Insights and Recommendations

This paper is a concise but valuable contribution to the field of wear-resistant surfacing. The authors clearly understand the application and the challenges of tungsten carbide surfacing, and they provide practical guidance that is immediately applicable.

My key takeaway for fellow engineers is that tungsten carbide surfacing is not a "set and forget" process. It requires careful control of the welding parameters, the carbide size and distribution, and the preheat and interpass temperatures. The cost of tungsten carbide consumables is high, so the process must be optimized to ensure that the deposit actually performs as designed.

I would recommend that the paper include more detail on the specific welding parameters and the consumable selection. In my experience, the difference between a surfacing job that lasts six months and one that lasts two years is often the choice of consumable and the control of the process parameters. A more detailed discussion of these factors would have strengthened the paper's practical value.

The paper is a good example of how a short technical article can provide useful guidance on a specific application. I hope it serves as a reference for engineers who are faced with the challenge of protecting components from severe abrasive wear.