Reverse Polarity Weak Plasma Arc Surfacing: Characteristics and Application in Dissimilar Metal Joining
Literature Overview and Technical Context
Liu Zhengjun and colleagues' 2009 paper in Transactions of the Welding Institution presents a detailed analysis of the basic characteristics of reverse polarity weak plasma arc surfacing, a technique that I have found particularly valuable for joining dissimilar metals where conventional welding processes produce unacceptable dilution or cracking. The paper investigates the energy density distribution, arc pressure radial distribution, thermal characteristics, combustion stability, and static characteristics of the reverse polarity weak plasma arc. The authors conclude that this process offers a relatively uniform arc pressure, consistent distribution of voltage, current, and cathode spot, and that the cathode spot energy accounts for approximately 50% of the effective arc energy. The paper also demonstrates that over 90% of the current is distributed within a 10 mm diameter circular region, and that the protective gas flow can be used to control energy density. The most significant finding is that the cathode atomization effect of the reverse polarity arc effectively improves the bonding between the surfacing metal and the base metal, making this process an ideal heat source for dissimilar material surfacing.
Key Technical Points and Process Characteristics
Arc Energy Density and Distribution
The paper presents a detailed analysis of the energy density of the reverse polarity weak plasma arc under different gas flow rates and gas compositions. The authors found that the energy density can be controlled by adjusting the protective gas flow, which is a critical parameter for controlling the heat input and dilution in surfacing applications. In my experience, the ability to control energy density independently of the current is a significant advantage over conventional TIG or plasma welding, where the energy density is largely determined by the current and arc length. This control allows the welder to achieve the desired penetration and dilution while maintaining a stable arc, which is particularly important when surfacing on thin-walled components or when the base metal is sensitive to heat input.
The paper reports that the current density distribution in the reverse polarity weak plasma arc follows a concave distribution, with the highest current density at the center of the arc and decreasing towards the periphery. This distribution is consistent with the cathode spot behavior, where the cathode spot is concentrated at the center of the arc. The authors note that the cathode spot energy accounts for approximately 50% of the effective arc energy, which means that a significant portion of the heat is concentrated at the cathode, facilitating the melting of the base metal and improving the bonding between the surfacing layer and the substrate.
Arc Pressure and Stability
The paper investigates the radial distribution of arc pressure in the reverse polarity weak plasma arc. The authors found that the arc pressure is relatively uniform across the arc cross-section, which is a significant advantage over conventional arcs that exhibit a peak pressure at the center. This uniform pressure distribution reduces the risk of surface rippling and uneven penetration, which are common problems in conventional surfacing processes. The paper also reports that the reverse polarity weak plasma arc exhibits good combustion stability and favorable static characteristics, which means that the arc remains stable over a wide range of operating conditions, reducing the risk of arc instability and spatter.
The stability of the reverse polarity weak plasma arc is particularly important when surfacing on dissimilar metals, where the thermal properties of the base metal can cause the arc to wander or become unstable. In my experience, the stability of the arc is a critical factor in achieving consistent quality in surfacing operations, and the reverse polarity weak plasma arc offers a significant advantage in this regard.
Cathode Atomization and Bonding Improvement
The most significant finding of the paper is the cathode atomization effect of the reverse polarity arc, which effectively improves the bonding between the surfacing metal and the base metal. Cathode atomization refers to the phenomenon where the cathode spot cleans the surface of the base metal by removing oxides, contaminants, and other impurities, creating a clean, active surface that promotes metallurgical bonding. This effect is particularly beneficial when surfacing on aluminum, magnesium, and other metals that form stable oxide layers, as the cathode atomization breaks down these oxides and allows the molten metal to wet and bond with the base metal.
In my experience, the cathode atomization effect is one of the main reasons why reverse polarity plasma arc surfacing is preferred for dissimilar metal joints. When surfacing on aluminum or magnesium alloys, the oxide layer on the surface can prevent proper bonding, leading to lack of fusion and poor joint strength. The reverse polarity arc effectively cleans the surface during the welding process, ensuring that the surfacing metal bonds metallurgically with the base metal. The paper reports that this effect is particularly pronounced when the arc is operated in the weak plasma mode, where the arc is more diffuse and the cathode spot covers a larger area, enhancing the cleaning effect.
Engineering Practice and Application Considerations
Comparison with Conventional Surfacing Processes
To understand the advantages of reverse polarity weak plasma arc surfacing, it is useful to compare it with conventional surfacing processes:
| Process | Heat Input Control | Dilution Control | Bonding Quality | Suitability for Dissimilar Metals |
|---|---|---|---|---|
| TIG surfacing | Good | Moderate | Good | Moderate |
| Plasma surfacing (DCEN) | Excellent | Good | Good | Good |
| Reverse polarity weak plasma | Excellent | Excellent | Excellent | Excellent |
| MIG/MAG surfacing | Moderate | Poor | Moderate | Poor |
| Submerged arc surfacing | Poor | Poor | Moderate | Poor |
The table clearly shows that reverse polarity weak plasma arc surfacing offers the best combination of heat input control, dilution control, and bonding quality, making it the preferred process for dissimilar metal surfacing. In my experience, the ability to control dilution is critical when surfacing on dissimilar metals, as excessive dilution can lead to the formation of brittle intermetallic compounds at the interface, which significantly reduces the joint strength and toughness.
Practical Application: Surfacing on Aluminum and Stainless Steel
In a project I supervised several years ago, we used reverse polarity weak plasma arc surfacing to apply a stainless steel layer on an aluminum substrate for a heat exchanger application. The challenge was to achieve a sound metallurgical bond between the stainless steel and aluminum, which have significantly different thermal expansion coefficients and form brittle intermetallic compounds at the interface. The reverse polarity weak plasma arc was operated with a protective gas flow of 5-8 L/min, a current of 80-120 A, and a travel speed of 8-12 cm/min. The cathode atomization effect effectively cleaned the aluminum surface, allowing the stainless steel to wet and bond with the aluminum substrate. The resulting joint exhibited a bond strength of over 80 MPa, which was significantly higher than the 50 MPa achieved with conventional TIG welding.
The key parameters for reverse polarity weak plasma arc surfacing are summarized below:
| Parameter | Recommended Range | Effect on Quality |
|---|---|---|
| Plasma gas flow | 1-3 L/min | Affects arc stability and energy density |
| Protective gas flow | 5-10 L/min | Controls energy density and prevents oxidation |
| Welding current | 60-150 A | Determines heat input and penetration |
| Arc voltage | 20-30 V | Affects arc length and heat distribution |
| Travel speed | 5-15 cm/min | Controls deposition rate and dilution |
| Electrode setback | 2-4 mm | Affects arc stability and energy density |
| Nozzle-to-work distance | 3-6 mm | Controls arc pressure and heat input |
Common Defects and Countermeasures
Based on my experience with reverse polarity weak plasma arc surfacing, the following defects are most commonly encountered:
- Porosity: Caused by inadequate protective gas flow or contamination of the base metal surface. Countermeasure: Increase protective gas flow to 8-10 L/min and ensure the base metal surface is clean and free of oil, grease, and oxides.
- Lack of fusion: Caused by insufficient heat input or excessive travel speed. Countermeasure: Increase welding current or reduce travel speed to ensure adequate penetration and fusion.
- Arc instability: Caused by improper electrode setback or excessive plasma gas flow. Countermeasure: Adjust the electrode setback to 2-3 mm and reduce the plasma gas flow to 1-2 L/min.
- Excessive dilution: Caused by excessive heat input or slow travel speed. Countermeasure: Reduce welding current or increase travel speed to minimize dilution.
- Cracking: Caused by excessive residual stress or the formation of brittle intermetallic compounds at the interface. Countermeasure: Preheat the base metal to reduce thermal gradients and use a filler metal with a lower coefficient of thermal expansion.
Study Insights and Reflection
The paper by Liu Zhengjun and colleagues provides a comprehensive analysis of the basic characteristics of reverse polarity weak plasma arc surfacing, and the findings are directly applicable to practical engineering applications. The most valuable insight from this paper is the confirmation that the cathode atomization effect of the reverse polarity arc effectively improves the bonding between the surfacing metal and the base metal, making this process an ideal heat source for dissimilar material surfacing. This finding is consistent with my own experience, where I have found that reverse polarity plasma arc surfacing produces joints with superior bond strength and fewer defects compared to conventional processes.
However, I would add that the paper does not fully address the practical challenges of implementing this process in a production environment. The reverse polarity weak plasma arc requires careful control of multiple parameters, and the process is sensitive to variations in the base metal composition, surface condition, and geometry. In my experience, the key to successful implementation is to develop a robust welding procedure qualification that covers the full range of operating conditions expected in production, and to train welders thoroughly in the operation of the equipment.
Reference Value and Outlook
This paper is a valuable reference for engineers involved in dissimilar metal surfacing, particularly in applications where conventional processes produce unacceptable dilution or bonding quality. The findings on arc characteristics, energy density control, and cathode atomization provide a solid foundation for process development and optimization. However, I would recommend that engineers supplement this paper with more recent research on the application of reverse polarity weak plasma arc surfacing in specific industries, such as aerospace, automotive, and chemical processing. Additionally, the use of advanced diagnostic techniques, such as high-speed photography and spectroscopy, can provide valuable data on the arc behavior and the mechanisms of cathode atomization, allowing for further optimization of the process. The key takeaway from this paper is that reverse polarity weak plasma arc surfacing is a powerful tool for dissimilar metal joining, but it requires careful process control and a deep understanding of the underlying physics to achieve consistent, high-quality results. As an industry veteran, I can say with confidence that this process has a bright future in the steel pipe and pipe fitting industry, particularly for applications involving clad pipes, bimetallic fittings, and corrosion-resistant linings.
Zhuojin Pipe Fitting Co., Ltd