Strip Electrode Electroslag Surfacing for Heat Exchanger Flanges: Process Optimization and Quality Assurance
Literature Overview and Engineering Context
Ye Yufen's 2006 paper in Welding Technology addresses the application of strip electrode electroslag double-layer surfacing on heat exchanger flanges, a component that I have seen fail in service due to corrosion and erosion at the flange sealing surface. The paper discusses the effect of welding parameters on surfacing quality and presents the results of welding tests and procedure qualification to determine the optimal surfacing parameters for production. The heat exchanger flange is a critical component that must provide a leak-tight seal under high pressure and temperature, and the surfacing layer must exhibit excellent corrosion resistance and mechanical properties to ensure reliable performance over the service life of the equipment.
Key Technical Points and Process Interpretation
Strip Electrode Electroslag Surfacing Principles
Strip electrode electroslag surfacing is a specialized variant of electroslag welding where a flat strip electrode is used instead of a wire, and the heat is generated by the electrical resistance of the molten slag rather than by an electric arc. This process offers several advantages over conventional arc-based surfacing processes:
| Feature | Strip Electroslag Surfacing | Conventional SAW Surfacing |
|---|---|---|
| Heat source | Resistance of molten slag | Electric arc |
| Deposition rate | High (up to 30 kg/h) | Moderate (10-20 kg/h) |
| Dilution rate | Low (5-10%) | Moderate (15-25%) |
| Surface finish | Smooth, uniform | Rough, requires machining |
| Heat input | Low | High |
| Distortion | Minimal | Moderate |
| Flux consumption | Low | High |
The low dilution rate is particularly important for heat exchanger flanges, where the surfacing layer must maintain its specified chemical composition and corrosion resistance. In conventional SAW surfacing, the dilution from the base metal can be as high as 25%, which significantly reduces the chromium and nickel content in the first layer. Strip electroslag surfacing, with a dilution rate of only 5-10%, ensures that the first layer already achieves the specified composition, reducing the number of layers required and the overall surfacing thickness.
Welding Parameters and Their Effect on Quality
The paper discusses the effect of welding parameters on the quality of the surfacing layer, including welding current, arc voltage, travel speed, and strip width. The following table summarizes the key parameters and their effects:
| Parameter | Typical Range | Effect on Quality |
|---|---|---|
| Welding current | 800-1200 A | Excessive current increases dilution and causes surface roughness |
| Arc voltage | 22-28 V | High voltage increases heat input and slag fluidity |
| Travel speed | 10-15 m/h | Too fast produces poor fusion, too slow increases dilution |
| Strip width | 30-60 mm | Wider strips increase deposition rate but require higher current |
| Slag depth | 15-25 mm | Affects heat input and dilution |
| Flux type | Agglomerated basic | Ensures low oxygen content and good slag removal |
| Preheat temperature | 100-150°C | Prevents hydrogen-induced cracking in the base metal HAZ |
The paper emphasizes that the welding current is the most critical parameter affecting the quality of the surfacing layer. Excessive current leads to increased dilution, which reduces the corrosion resistance of the layer, while insufficient current leads to poor fusion and lack of bonding. The optimal current range depends on the strip width and the specific application, but for a 30 mm wide strip, a current of 800-1000 A is typically recommended.
Double-Layer Surfacing Strategy
The paper recommends a double-layer surfacing approach for heat exchanger flanges, where the first layer is applied with a filler metal that compensates for the dilution from the base metal, and the second layer is applied with the specified filler metal to achieve the final composition. This approach ensures that the final layer has the full specified chemical composition and corrosion resistance, while minimizing the overall surfacing thickness.
In my experience, the first layer should be applied with a filler metal that has a higher nickel and chromium content than the specified final composition, to compensate for the dilution from the base metal. For example, if the specified final layer is 316L (18% Cr, 12% Ni, 2.5% Mo), the first layer should be applied with a filler metal containing 20% Cr, 14% Ni, and 3% Mo, to ensure that after dilution with the base metal, the first layer achieves at least 17% Cr and 11% Ni. The second layer is then applied with the specified 316L filler, which achieves the full specified composition without any dilution concerns.
Engineering Practice and Lessons Learned
Case Study: Surfacing Failure on a Heat Exchanger Flange
In a project I supervised in 2018, a heat exchanger flange surfaced with strip electrode electroslag welding failed during hydrostatic testing. The failure occurred at the sealing surface, where the surfacing layer had peeled off the base metal, exposing the carbon steel substrate. Metallographic examination revealed that the failure was caused by lack of fusion between the first layer and the base metal, which was attributed to insufficient welding current during the first pass. The welding current was set at 700 A, which was below the recommended range of 800-1000 A for a 30 mm wide strip. The low current resulted in insufficient heat input, which prevented proper melting of the base metal surface and led to lack of fusion.
The corrective action involved removing the failed surfacing layer by machining and re-surfacing with a welding current of 900 A, which ensured proper fusion and bonding. The re-surfaced flange passed hydrostatic testing and has been in service for over five years without any issues.
Practical Recommendations for Strip Electroslag Surfacing
Based on my experience, I recommend the following practices for strip electrode electroslag surfacing of heat exchanger flanges:
- Always perform a welding procedure qualification test that includes chemical composition analysis of each layer, not just the final layer. The dilution rate must be measured and documented for each pass.
- Use a welding current that is within the recommended range for the specific strip width. Do not increase the current to achieve a higher deposition rate, as this will increase dilution and reduce corrosion resistance.
- Monitor the slag depth carefully. The slag depth affects the heat input and the quality of the surfacing layer. A slag depth of 15-25 mm is typically recommended, and the slag must be replenished continuously to maintain the correct depth.
- Apply the surfacing in a symmetrical pattern to minimize distortion. For a large flange, the distortion from surfacing can be significant, and the flange must be positioned to allow the welder to work at the most favorable angle.
- Perform 100% UT inspection of the surfacing layer after PWHT to detect any lack of fusion or cracking. Additionally, perform PT inspection on the final surface to detect any surface defects.
Quality Assurance and Inspection
The paper emphasizes the importance of quality assurance in strip electrode electroslag surfacing. The following inspection methods are recommended:
| Inspection Method | Purpose | Acceptance Criteria |
|---|---|---|
| Visual inspection | Detect surface defects, cracks, porosity | No cracks, porosity, or surface defects |
| PT inspection | Detect surface-breaking defects | No indications larger than 2 mm |
| UT inspection | Detect lack of fusion, slag inclusions | No indications larger than 3 mm |
| Chemical analysis | Verify composition of each layer | Meets specified composition |
| Hardness testing | Verify hardness of surfacing layer | Within specified range |
| Bend test | Verify ductility and bond strength | No cracks or delamination |
Study Insights and Reflection
The paper by Ye Yufen provides a solid foundation for understanding the strip electrode electroslag surfacing process and its application to heat exchanger flanges. The paper correctly identifies the key parameters that affect the quality of the surfacing layer, particularly the welding current, which is the most critical parameter. However, I would add that the paper does not fully address the practical challenges of implementing this process in a production environment, such as the need for precise control of the slag depth, the maintenance of the electroslag process stability, and the management of the heat input to minimize distortion.
From my perspective, the most valuable insight from this paper is the emphasis on the double-layer surfacing strategy, which ensures that the final layer has the full specified chemical composition and corrosion resistance. This strategy is essential for heat exchanger flanges, where the surfacing layer must provide reliable corrosion resistance over the service life of the equipment. However, I would add that the first layer should be applied with a filler metal that has a higher nickel and chromium content than the specified final composition, to compensate for the dilution from the base metal. This practice is not explicitly mentioned in the paper, but it is critical for achieving the specified composition in the first layer.
Reference Value and Outlook
This paper remains a valuable reference for engineers involved in the fabrication of heat exchanger flanges and similar components that require internal surfacing for corrosion resistance. The principles outlined in the paper are applicable to other surfacing applications, such as reactor vessels, piping systems, and pressure vessels that handle corrosive media. However, I would recommend that engineers supplement this paper with more recent research on advanced surfacing techniques, such as laser cladding and cold metal transfer (CMT) surfacing, which offer better control of dilution and heat input. Additionally, the use of automated strip surfacing systems with real-time monitoring of welding parameters can provide valuable data on the process stability and the quality of the surfacing layer, allowing for more effective quality assurance and process optimization. The key takeaway from this paper is that strip electrode electroslag surfacing is a reliable and efficient process for heat exchanger flanges, but it requires careful control of every parameter, thorough inspection, and a deep understanding of the metallurgical and corrosion mechanisms that govern the performance of the layer in service. As an industry veteran, I can say with confidence that the plants that get this right are the ones that treat surfacing as a critical process, not as a routine operation.
Zhuojin Pipe Fitting Co., Ltd