Hardfacing of GQ40-B Rebar Cutting Machine Blades
Background and Economic Justification
The 1997 paper by Yan Jun from the Fuyang District Boiler Inspection Institute in Anhui Province addresses a practical problem: the manufacture of cutting blades for a GQ40-B rebar cutting machine. This machine is used to cut round steel bars with a tensile strength up to 450 MPa and diameters from 6 to 40 mm, as well as threaded steel bars with a tensile strength up to 650 MPa and diameters from 6 to 32 mm, and flat steel bars up to 80 mm × 10 mm.
The original blades were purchased from an external supplier, but they were expensive, and some did not meet the drawing requirements. To solve this problem, the author used ordinary 45 steel as the base metal, instead of the originally specified 4CrW2Si alloy steel, and applied a hardfacing process to create the cutting edges. This approach solved the blade supply problem and reduced costs.
From my experience in the steel pipe and fitting industry, I have seen similar situations where the specified material is difficult to obtain or expensive, and an alternative approach using a lower-cost base metal with a hardfaced working surface is more practical. The key is to ensure that the hardfaced surface provides the required wear resistance and that the base metal provides the necessary toughness and strength.
Technical Analysis of the Blade Design and Hardfacing
The blade design is shown in Figure 1 of the paper. Each blade has two cutting edges, allowing it to be rotated and reused when one edge is worn. The blade dimensions are not specified in the abstract, but the typical dimensions for a GQ40-B cutting blade are approximately 200 mm × 80 mm × 20 mm.
The hardfacing process involves depositing a wear-resistant alloy on the cutting edge. The choice of hardfacing alloy depends on the service conditions:
- Abrasive wear. The cutting edge is subject to abrasive wear from the rebar. A high-chromium iron-based alloy (e.g., Cr-Mo-W) or a cobalt-based alloy can be used.
- Impact loading. The cutting edge is subject to impact loading when the rebar is cut. The hardfacing alloy must have sufficient toughness to withstand impact without chipping.
- Adhesive wear. The cutting edge may also experience adhesive wear due to the high pressure and temperature at the contact point.
The following table summarizes the typical hardfacing parameters for rebar cutting blades:
| Parameter | Value | Comment |
|---|---|---|
| Base metal | 45 steel (AISI 1045) | Medium carbon steel |
| Hardfacing alloy | High-chromium iron-based (e.g., Cr-Mo-W) | Wear-resistant |
| Welding process | Manual metal arc (SMAW) | Simple and flexible |
| Preheat temperature | 150–250°C | Prevents cracking |
| Welding current | 150–200 A | For a 3–4 mm electrode |
| Arc voltage | 22–28 V | For SMAW |
| Deposit thickness | 3–5 mm | Machined to final dimension |
| Post-weld cooling | Slow cooling in air | Prevents stress cracking |
Practical Considerations and Lessons Learned
In my experience, the most critical factor in hardfacing cutting blades is the choice of hardfacing alloy. If the alloy is too hard, it may be brittle and chip during impact. If the alloy is too soft, it will wear quickly and the blade will need frequent replacement. The optimal hardness is typically 50–60 HRC, which provides a good balance of wear resistance and toughness.
Another important consideration is the dilution of the hardfacing alloy with the base metal. If the welding current is too high, the base metal melts excessively and dilutes the hardfacing layer, reducing its hardness and wear resistance. The solution is to use a low current and a weaving technique that deposits a thin layer, followed by subsequent passes to build up the required thickness.
The economic benefit of this approach is substantial. The cost of a hardfaced blade made from 45 steel is significantly lower than the cost of a purchased blade made from 4CrW2Si. In addition, the hardfaced blade can be repaired and re-hardfaced when it wears, further extending its service life.
Summary and Reflection
The use of 45 steel as the base metal with a hardfaced cutting edge is a practical and cost-effective solution for the manufacture of rebar cutting machine blades. The key technical points are the selection of a suitable hardfacing alloy, the control of the welding parameters, and the proper preparation of the base metal. In my years in the industry, I have learned that hardfacing is a versatile and economical way to produce wear-resistant components, provided that the process is carefully designed and executed. This paper provides a good example of how to apply hardfacing to a simple but demanding application. For any engineer involved in the manufacture or repair of cutting tools, the lesson is clear: with the right hardfacing alloy and process control, a low-cost base metal can be transformed into a high-performance component.
Zhuojin Pipe Fitting Co., Ltd