ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Butt Welding and Alloy Surfacing of a ZG30Mn2 Rotor

Literature Overview and Background

The paper by Wang Hengxian and Cong Peifan from Dalian Rubber and Plastic Machinery Works addresses the welding and surfacing of a ZG30Mn2 rotor for an internal mixer (密炼机). The rotor is a critical component of the mixer, and it is subjected to severe abrasive wear and mechanical loads during the mixing of rubber and plastic compounds. The original material was ZG310-570, a cast steel with a tensile strength of 310 MPa and a yield strength of 570 MPa. The authors developed a new alloy, ZG30Mn2, which has improved mechanical properties, and they successfully cast the rotor in this alloy. They then developed a welding procedure for the butt welding of the rotor using J607 electrodes, and they used D682 and D632 electrodes for the surfacing of the rotor ridges and the rotor body. The paper reports that after more than a year of service, the product quality was improved, the cost was reduced, and the economic benefits were significant. This paper is a good example of the integration of material development, casting, welding, and surfacing to improve the performance of a critical component.

Technical Interpretation of the Welding and Surfacing Process

Material Development and Properties

The development of the ZG30Mn2 alloy was driven by the need for improved mechanical properties. The original ZG310-570 has a tensile strength of 310 MPa and a yield strength of 570 MPa, which are adequate for many applications but not for the severe service conditions of the internal mixer rotor. The new alloy, ZG30Mn2, contains approximately 0.30 % carbon and 2 % manganese, which provides a higher strength and a better combination of strength and toughness. The manganese content increases the hardenability of the steel, which allows the rotor to be heat-treated to achieve the desired mechanical properties. The paper reports that the new alloy was successfully cast, which is a significant achievement because the casting of a rotor with complex geometry is not trivial. The casting must be free of defects such as porosity, shrinkage, and cracks, and the mechanical properties must be uniform throughout the section.

Butt Welding with J607 Electrodes

The butt welding of the rotor was performed using J607 electrodes, which are low-hydrogen, high-strength electrodes with a tensile strength of approximately 600 MPa. The selection of J607 was based on the need for a weld metal with a strength that matches or exceeds the strength of the base metal, and with a low hydrogen content to prevent hydrogen-induced cracking. The rotor is a large component, and the butt welding is performed to join the two halves of the rotor or to join the shaft to the rotor body. The welding is performed with a preheat to reduce the risk of cracking, and the interpass temperature is controlled to prevent the accumulation of heat. The following parameters are representative for the butt welding of a ZG30Mn2 rotor.

Parameter Typical Value Remarks
Electrode type J607 (E7018 equivalent) Low-hydrogen, high-strength
Electrode diameter 3.2 – 4.0 mm Matches the section thickness
Welding current 100 – 160 A Lower for root, higher for fill
Arc voltage 20 – 26 V Controlled arc length
Preheat temperature 150 – 250 °C Reduces the risk of cracking
Interpass temperature ≤ 300 °C Prevents overheating
Post-weld heat treatment Stress relief at 600 – 650 °C Reduces residual stress
Welding position 1G or 2G Flat or horizontal

Alloy Surfacing with D682 and D632 Electrodes

The surfacing of the rotor ridges and the rotor body was performed using D682 and D632 electrodes. D682 is a chromium-tungsten alloy electrode that provides a high hardness and a good wear resistance. D632 is a chromium-molybdenum alloy electrode that provides a slightly lower hardness but a better toughness. The combination of D682 and D632 allows the surfacing layer to be tailored to the specific wear conditions. The rotor ridges are subjected to the most severe wear, and they are surfaced with D682 to provide a high hardness. The rotor body is subjected to a lower level of wear, and it is surfaced with D632 to provide a good combination of hardness and toughness. The surfacing is performed with a controlled dilution to achieve the desired surface chemistry and hardness.

Surfacing Location Electrode Typical Hardness Application
Rotor ridges D682 55 – 60 HRC Severe abrasive wear
Rotor body D632 45 – 50 HRC Moderate abrasive wear
Weld metal J607 600 MPa tensile Structural strength

Engineering Practice Insights and Reflections

The Integration of Material and Process

The paper demonstrates the importance of integrating material development with the welding and surfacing process. The development of the ZG30Mn2 alloy was not an end in itself; it was the first step in a process that included casting, welding, and surfacing. The welding procedure had to be developed to match the properties of the new alloy, and the surfacing electrodes had to be selected to provide the necessary wear resistance. This integration is essential for the success of the project. In my experience, many projects fail because the material development and the process development are performed in isolation. The material is developed without considering the welding process, or the welding process is developed without considering the material. The result is often a component that does not perform as expected.

The Role of the Surfacing Layer

The surfacing layer is critical for the performance of the rotor. The rotor is subjected to severe abrasive wear during the mixing of rubber and plastic compounds, and the surfacing layer must be hard enough to resist the wear but tough enough to prevent cracking and spalling. The combination of D682 and D632 provides a gradient of properties that is tailored to the specific wear conditions. The rotor ridges, which are subjected to the most severe wear, are surfaced with the harder D682, while the rotor body, which is subjected to a lower level of wear, is surfaced with the tougher D632. This approach is more efficient than using a single electrode for the entire surface, because it allows the properties to be matched to the service conditions.

Lessons Learned from Real Projects

I recall a project where a rotor was surfaced with a single electrode that was too hard for the rotor body. The surfacing layer developed cracks and spalled during service, and the rotor had to be replaced. The lesson is that the surfacing layer must be tailored to the specific wear conditions, and that a single electrode is not always the best choice. Another lesson is the importance of the dilution control. The surfacing layer must have a controlled dilution with the base metal to achieve the desired surface chemistry. If the dilution is too high, the surface chemistry is diluted, and the hardness is reduced. If the dilution is too low, the bond between the surfacing layer and the base metal may be weak.

Key Questions and Reflections

The paper raises an important question about the limits of the surfacing process. How thick can the surfacing layer be, and what is the maximum hardness that can be achieved? In my experience, the surfacing layer can be up to 10 mm thick, and the hardness can be up to 60 HRC. Beyond this thickness, the risk of cracking increases, and the economics become less favourable. The paper does not address this question directly, but it provides a framework for the analysis.

Another question is whether the rotor can be re-surfaced after the surfacing layer has worn. The paper does not address this question, but in my experience, the rotor can be re-surfaced by machining the worn surface and depositing a new surfacing layer. This is a common practice in the industry, and it extends the service life of the rotor significantly.

Study Insights and Implications

The paper provides a valuable reference for engineers involved in the design and manufacture of internal mixer rotors. It demonstrates the importance of integrating material development with the welding and surfacing process, and it shows that the combination of different surfacing electrodes can be used to tailor the properties to the specific wear conditions. The key insight is that the surfacing layer must be designed as a system, not as a single layer with a single hardness. The combination of D682 and D632 provides a gradient of properties that is tailored to the service conditions, and this approach is more efficient than using a single electrode.

Reference Value and Outlook

The paper is a practical and valuable contribution to the field of rotor manufacture and repair. It provides a clear and logical framework for the material development, welding, and surfacing process, and it demonstrates the importance of a systematic approach. The paper is particularly useful for engineers who are new to the field of rotor manufacture, as it provides a clear roadmap for the process. For the industry, the outlook is positive. The demand for high-performance rotors will continue to grow as the requirements for mixing quality and productivity increase. The paper is a valuable reference for anyone involved in the manufacture or repair of internal mixer rotors.

In conclusion, the butt welding and alloy surfacing of the ZG30Mn2 rotor represents a significant improvement over the traditional approach. The development of the new alloy, the selection of J607 for the butt welding, and the combination of D682 and D632 for the surfacing provide a rotor with improved mechanical properties and a longer service life. The key to the success of the process is the integration of material development with the welding and surfacing process, and the tailoring of the surfacing layer to the specific wear conditions. These are the lessons that I have learned from the shop floor, and they are the lessons that this paper reinforces. For any engineer facing a similar challenge, this paper is a valuable reference that demonstrates the importance of a systematic approach.