ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Plasma Arc Powder Surfacing of Aluminum Bronze on 20g Steel: Interface Metallurgy and Process Control

Literature Overview and Core Findings

The paper by Liu Zhengjun and colleagues at Shenyang University of Technology addresses a classic dissimilar-metal problem: depositing aluminum bronze (Cu-Al alloy) onto 20g carbon steel using a reverse-polarity weak plasma arc with powder feed. The work is directly relevant to our industry because copper alloy overlays on steel are widely used in valve seats, bearing surfaces, guide plates, and chemical equipment linings where the combination of corrosion resistance and wear resistance is required.

The core finding is that welding current is the master variable governing interface quality. At 110 A, the deposit consists of dense α-Cu with a network of (α+γ₂) eutectoid structure, giving the best combination of mechanical properties and soundness. As current increases, heat input rises and the "泛铁" (iron dilution / iron pickup) phenomenon intensifies at the interface. At excessive currents, penetration cracks appear in the fusion zone. The authors attribute these cracks to three synergistic factors: welding residual stress, capillary effect, and low-melting-point eutectic formation during cooling.

Technical Interpretation and Process Windows

The Role of Polarity and Plasma Arc Characteristics

The choice of reverse polarity (DCEP) with a weak plasma arc is deliberate. In direct current electrode negative (DCEN), the arc concentrates heat on the workpiece, causing deep penetration and excessive dilution of the copper alloy with iron from the base metal. Iron pickup degrades the corrosion resistance and mechanical properties of the aluminum bronze overlay. Reverse polarity distributes heat more evenly, reduces penetration depth, and allows the powder to deposit with minimal base metal melting.

The "weak plasma arc" terminology indicates a low-current, low-energy plasma transferred arc (PTA) process. This is critical because conventional plasma arc welding with high current would produce excessive dilution and mixing. The authors' process window at 110 A represents a sweet spot where the arc is stable, the powder melts fully, and the dilution rate remains acceptable.

The "泛铁" Phenomenon and Its Consequences

"泛铁" literally means "iron floating up" — iron from the base metal melts, mixes into the molten pool, and rises toward the surface of the copper alloy deposit. This is the most common defect in copper-on-steel surfacing. The consequences are:

Parameter Effect on Interface Quality
Low current (< 100 A) Insufficient melting, poor fusion, porosity
Optimal current (~ 110 A) Dense α-Cu + (α+γ₂) network, good fusion, minimal dilution
Moderate overcurrent (120-140 A) Increased dilution, "泛铁" begins, mechanical properties degrade
Excessive current (> 140 A) Severe dilution, penetration cracks, eutectic formation at interface

The eutectic structure (α+γ₂) is actually beneficial when present in the right proportion. γ₂ is a hard intermetallic phase that provides wear resistance. However, when dilution increases, the iron content rises, promoting the formation of brittle Fe-Al intermetallics and low-melting eutectics that solidify last and concentrate at grain boundaries.

Penetration Crack Mechanism

The authors' explanation of penetration cracks is particularly valuable. These cracks initiate at the interface and propagate into the base metal. The mechanism involves:

  1. Welding residual stress: The thermal expansion mismatch between copper alloy (coefficient ~17×10⁻⁶/°C) and steel (~12×10⁻⁶/°C) generates significant stress at the interface during cooling.
  2. Capillary effect: Molten copper alloy has excellent wettability on steel. When the interface is not fully fused, liquid copper can penetrate into micro-cracks or grain boundaries of the steel, acting as a wedge.
  3. Low-melting eutectics: During cooling, the last solidifying liquid is enriched in low-melting elements (Cu, Al, and impurities), forming eutectic films at grain boundaries that have low ductility and act as crack initiation sites.

The combination of these three factors — stress concentration, capillary-driven liquid penetration, and brittle eutectic films — creates a classic solidification cracking scenario that is very difficult to eliminate once initiated.

Integration with Engineering Practice

Practical Implications for Dissimilar Metal Overlays

In my experience with valve seats, pump components, and chemical equipment linings, the lessons from this paper align with what we see on the shop floor:

  1. Current control is paramount. Operators often increase current to speed up deposition, not realizing they are trading quality for productivity. A 20% current increase can double the dilution rate and eliminate the corrosion resistance that justified the overlay in the first place.
  2. Preheat and interpass temperature management. The paper does not emphasize preheat, but in practice, preheating the steel substrate to 150-200°C reduces the thermal gradient and helps prevent cracking. However, excessive preheat increases dilution. The balance is delicate.
  3. Post-weld heat treatment. For aluminum bronze overlays, a post-weld stress relief at 300-400°C is often beneficial, but it must be below the temperature where the eutectoid transformation occurs.

Real-World Case: Valve Seat Overlay Failure

I recall a case where a batch of 6-inch gate valves with aluminum bronze seat overlays failed during hydrostatic testing. The overlays looked sound on the surface, but UT revealed lack of fusion at the interface. Investigation showed the welder had increased current by 30% to meet production schedule. The result was excessive dilution, iron pickup, and brittle interface structure. The entire batch had to be scrapped and re-overlaid with proper process control.

Process Control Recommendations

Control Parameter Recommended Range Monitoring Method
Welding current 100-120 A (for 20g steel) Ammeter, data logger
Arc voltage 20-28 V Voltmeter
Powder feed rate 20-35 g/min Calibrated feeder
Travel speed 80-120 mm/min Tachometer
Shielding gas flow 10-15 L/min (Ar) Flow meter
Preheat temperature 100-150°C Contact pyrometer
Interpass temperature ≤ 200°C IR thermometer

Key Questions and Reflections

What the Paper Does Not Tell Us

The paper focuses on 20g steel, but in practice we overlay on a range of carbon steels, low-alloy steels, and even stainless steels. The optimal current window shifts with base metal thermal conductivity and thickness. A thicker section acts as a heat sink, requiring higher current to achieve fusion, but this also increases dilution.

The paper does not address the effect of powder composition. Aluminum bronze powder with higher aluminum content (10-12% Al) produces more γ₂ phase and higher hardness but also more brittleness. The trade-off between hardness and toughness must be balanced based on service requirements.

The Capillary Effect — A Hidden Danger

The capillary effect described in the paper is often underestimated in practice. When the interface has micro-cracks from prior machining or thermal cycling, molten copper can penetrate deep into these defects. This is especially dangerous in service where thermal cycling can propagate these cracks. I have seen cases where copper overlay cracks initiated at the interface and propagated through the base metal during service, leading to catastrophic failure.

Study Insights and Implications

This paper reinforces several fundamental lessons that apply to all dissimilar metal surfacing:

  1. Dilution is the enemy. Every dissimilar metal overlay process must be designed to minimize dilution while maintaining fusion. The process window is narrow, and it must be respected.
  2. Interface is the weakest link. The fusion zone between dissimilar metals is inherently heterogeneous. It contains gradients of composition, microstructure, and properties. It is where failures initiate.
  3. Process parameters are interconnected. Current, voltage, travel speed, and powder feed rate cannot be optimized independently. They must be tuned together to achieve the desired dilution rate and deposit geometry.
  4. Nondestructive testing is essential. UT and RT are mandatory for critical overlays. The interface is where defects hide, and surface inspection alone is insufficient.

Reference Value and Outlook

For engineers involved in dissimilar metal surfacing, this paper provides a solid foundation for understanding the interface metallurgy of copper alloys on steel. The identification of the three-factor crack mechanism (stress + capillary + eutectic) is particularly valuable because it explains why cracks occur even when welding parameters appear reasonable.

Looking ahead, the industry is moving toward laser cladding and cold metal transfer (CMT) processes that offer better dilution control. However, plasma arc powder surfacing remains a cost-effective option for many applications, especially where the overlay area is large and the geometry is simple.

The key takeaway is that process control is not optional. In dissimilar metal surfacing, the difference between a good overlay and a failed one is often just a few amps of current. The veteran's rule: "When in doubt, lower the current and slow down."