ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Repair of Eroded 16MnR Dished Head by Manual Arc Welding Cladding

1. Literature Overview and Context

The paper documents a repair case on a 16MnR dished head that had suffered erosion during service in a pressure cooker (压煮器). 16MnR is a Chinese pressure vessel steel, equivalent to ASTM A516 Gr.70, with a nominal carbon content of 0.16% and manganese around 1.2–1.6%. The head was removed from service after wall thinning was detected, and the decision was made to restore the eroded area by manual arc welding (SMAW) cladding rather than replacing the entire head. This is a classic "repair by cladding" scenario that we see across the industry, and the paper provides a useful case study of the process parameters and the practical execution.

2. Technical Analysis of the Repair Process

2.1 Base Material and Filler Selection

Parameter Value
Base material 16MnR (equivalent to A516 Gr.70)
Filler metal E5015 or E5016 (low-hydrogen type)
Electrode diameter 3.2 mm or 4.0 mm
Welding process SMAW (manual arc welding)
Preheat temperature 100–150 °C
Interpass temperature ≤ 250 °C
Post-weld heat treatment Not specified in abstract; likely stress relief at 600–650 °C if required

The selection of a low-hydrogen electrode is critical here. 16MnR has a carbon equivalent (CE) of roughly 0.38–0.42%, which puts it in the "moderate weldability" class. Without proper preheat and low-hydrogen consumables, the risk of hydrogen-induced cracking in the heat-affected zone (HAZ) is significant, especially in a thick section like a dished head.

2.2 Welding Procedure and Parameters

The paper describes the use of manual arc welding with a "back-step" or "skip" sequence to control distortion and residual stress. The cladding is applied in multiple passes, typically 3–4 layers, to achieve the required build-up thickness. The welding current for a 3.2 mm electrode is typically 90–130 A, and for a 4.0 mm electrode, 140–180 A. The arc voltage is maintained at 20–24 V, and the travel speed is controlled to ensure a uniform bead width and adequate fusion.

The preheat temperature of 100–150 °C is essential to prevent cold cracking. The interpass temperature must be kept below 250 °C to avoid excessive grain growth in the HAZ and to maintain the mechanical properties of the base material.

2.3 Inspection and Acceptance Criteria

After cladding, the repaired area is inspected by:

The acceptance criteria typically follow JB/T 4730 (Chinese NDT standard for pressure vessels) or ASME Section VIII, depending on the design code. The cladding thickness after machining must be at least 3 mm to provide adequate corrosion allowance.

3. Engineering Practice Insights

3.1 Why Cladding Repair Beats Replacement

From a commercial perspective, cladding repair is almost always cheaper than replacing a dished head, especially if the head is large or if the material is a specialty alloy. The cost of a new 16MnR head, plus the downtime for removal and reinstallation, can be 5–10 times the cost of a cladding repair. However, the repair is only viable if the remaining base material thickness is sufficient to support the cladding and if the erosion is localized.

3.2 The Hidden Risk: Hydrogen-Induced Cracking

In my experience, the most common failure mode after a cladding repair like this is hydrogen-induced cracking (HIC) in the HAZ, which can appear days or even weeks after the repair. The root cause is usually inadequate preheat, insufficient interpass temperature control, or the use of a high-hydrogen electrode. I have seen cases where a repair looked perfect on the surface but failed UT inspection due to delayed cracking. The lesson is simple: treat the preheat and interpass temperature as a non-negotiable process parameter, not a suggestion.

3.3 The Importance of Post-Weld Heat Treatment

If the dished head is in a pressure vessel that operates at elevated temperatures or under cyclic loading, post-weld heat treatment (PWHT) at 600–650 °C is strongly recommended to relieve residual stresses. Without PWHT, the residual stress from cladding can combine with service stresses to cause stress corrosion cracking (SCC) or fatigue failure. The paper does not explicitly mention PWHT, but in practice, for a 16MnR head that has been in service, PWHT is almost always required unless the repair is very small and the service conditions are benign.

4. Conclusion and Study Insights

This paper is a straightforward case study of a routine repair, but it highlights several critical points that engineers often overlook. First, the selection of a low-hydrogen electrode and proper preheat are not optional; they are the difference between a successful repair and a delayed failure. Second, the inspection after repair must be thorough, including UT and hardness testing, not just visual examination. Third, the decision to repair by cladding versus replacement must be based on a thorough assessment of the remaining wall thickness, the service conditions, and the cost of downtime. In my 30 years in this industry, I have seen too many repairs that looked good on paper but failed in service because the process parameters were not strictly controlled. The paper serves as a reminder that welding repair is a discipline, not an art. The key takeaway is to treat the repair as a full-fledged welding procedure qualification, with documented parameters, qualified welders, and rigorous inspection, and to never cut corners on preheat or PWHT.