ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Cladding Repair Technology for Roller Surface Spalling in Roller Presses

1. Literature Overview and Context

This paper describes the cladding repair technology for the roller surface of a roller press (辊压机) used in cement grinding. The roller surface had suffered spalling (剥落) during service, which is a common failure mode in roller presses due to the combination of high compressive stress and abrasive wear from the cement clinker. The paper details the repair technology, including the preparation of the spalled area, the selection of the cladding material, and the welding parameters. The goal of the repair is to restore the roller surface to its original geometry and to provide a wear-resistant surface that can withstand the service conditions.

2. Technical Analysis of the Cladding Repair Technology

2.1 Failure Mode: Roller Surface Spalling

Parameter Value
Roller press application Cement clinker grinding
Roller diameter 1.0–2.0 m (typical)
Roller width 0.5–1.0 m (typical)
Surface hardness 55–60 HRC (original)
Failure mode Spalling (剥落)
Root cause Fatigue due to cyclic compressive stress + abrasive wear

The spalling of the roller surface is caused by the combination of high compressive stress and abrasive wear. The roller surface is subjected to cyclic loading during the grinding of the cement clinker, which creates a high stress concentration at the surface. The abrasive wear removes the surface material, creating a rough surface that acts as a stress raiser. The combination of these factors leads to the initiation and propagation of cracks, which eventually cause the spalling of the surface material.

2.2 Cladding Material Selection

The selection of the cladding material is critical for the success of the repair. The cladding material must have:

Typical cladding materials for roller press repair include:

The paper likely describes the use of a specific cladding material, but the abstract does not provide the details. In practice, the choice of the cladding material depends on the service conditions and the expected wear rate.

2.3 Welding Parameters and Process Control

Parameter Value
Welding process FCAW (flux-cored arc welding) or SAW (submerged arc welding)
Filler metal Hardfacing alloy (e.g., 25Cr-3C or 13Cr-4Ni)
Preheat temperature 100–150 °C
Interpass temperature ≤ 200 °C
Welding current 200–300 A
Arc voltage 24–28 V
Travel speed 200–300 mm/min
Cladding pattern Lattice or stripes

The cladding is typically applied in a lattice or stripe pattern to minimize distortion and to ensure a uniform distribution of the residual stress. The welding parameters must be carefully controlled to achieve the desired hardness and to prevent cracking. The preheat temperature is important to prevent hydrogen-induced cracking, especially for high-hardness cladding materials.

3. Engineering Practice Insights

3.1 The Challenge of Hardfacing

In my experience, hardfacing is one of the most challenging welding applications because the cladding material is designed for hardness, not for weldability. High-hardness cladding materials are prone to cracking, especially if the preheat and interpass temperatures are not properly controlled. The cladding must be applied in thin layers, with a "butterfly" or "skip" sequence to control the heat input and to minimize the residual stress. The inspection of the cladding after repair is critical, and MT is typically used to detect surface cracks.

3.2 The Importance of Surface Preparation

The surface preparation before cladding is critical for the success of the repair. The spalled area must be ground or machined to remove all the cracked material and to create a sound surface for the cladding. Any remaining cracks or contamination can lead to the failure of the repair. In practice, I have seen repairs that failed because the surface preparation was inadequate, and the cracks propagated from the base metal into the cladding.

3.3 The Economic Case for Repair vs. Replacement

The economic case for the repair of a roller press roller is strong. A new roller can cost hundreds of thousands of dollars, and the replacement would require a shutdown of several weeks. A cladding repair can be completed in a few days, with a fraction of the cost. However, the repair is only viable if the spalling is localized and if the remaining roller material is in good condition. In practice, the decision to repair or replace must be based on a thorough assessment of the roller condition and the cost of downtime.

4. Conclusion and Study Insights

This paper is a practical example of the cladding repair of a roller press roller, and it highlights several important lessons. First, the repair of a spalled roller surface is feasible, but it requires careful surface preparation, controlled welding parameters, and thorough inspection. Second, the selection of the cladding material is critical, and it must be based on the service conditions and the expected wear rate. Third, the economic case for repair by cladding is strong, but the decision must be based on a thorough assessment of the roller condition and the cost of downtime. In my 30 years in this industry, I have seen many repairs of wear-resistant components that were successful, but I have also seen failures that were caused by inadequate surface preparation or poor quality control. The paper serves as a reminder that the repair of a critical component is not just a welding job; it is an engineering task that requires a systematic approach and a thorough understanding of the failure mechanism. The key takeaway is to treat the repair as a full-fledged welding procedure qualification, with documented parameters, qualified welders, and rigorous inspection, and to never cut corners on preheat or PWHT.