ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Repair of the Impeller of a Salt Circulation Pump by Surfacing Welding

Literature Overview and Core Technical Content

The paper by Wang Qilong, published in China Well and Rock Salt in 1996, describes the repair of the impeller of a salt circulation pump in a salt mine. The pump is used to circulate brine, and the impeller suffers severe wear and corrosion due to the abrasive and corrosive nature of the brine. The paper describes a surfacing welding repair procedure that was used to extend the life of the impeller. The paper is a practical case study, and it provides valuable information about the challenges of repairing components in a corrosive environment.

Interpretation of Technical Points and Process Windows

The salt circulation pump is a critical piece of equipment in a salt mine. It circulates brine from the mine to the processing plant, and it operates continuously. The impeller is the main rotating component, and it is subjected to both abrasive wear from the salt crystals and corrosion from the brine. The combination of abrasion and corrosion is particularly damaging, because the corrosion removes the protective oxide layer, exposing fresh metal to the abrasive action of the salt crystals. The impeller is typically made of a cast iron or stainless steel, and it may be coated or treated to improve its resistance to wear and corrosion.

The repair procedure involves surfacing welding to build up the worn areas of the impeller. The paper does not provide detailed welding parameters, but it is clear that the repair is a build-up operation. The choice of welding consumable is critical. For a component that is subject to both abrasion and corrosion, a nickel-based or cobalt-based alloy is often used. These alloys have good corrosion resistance and can work-harden under abrasion. The paper does not specify the consumable used, but it is likely a nickel-based alloy, given the corrosive environment.

Engineering Practice and Lessons Learned

This paper is a good example of the "repair rather than replace" philosophy in a corrosive environment. The cost of a new impeller is significant, and the downtime required to replace it is substantial. By performing surfacing repair, the plant was able to extend the life of the impeller and avoid a major capital expenditure. However, I have seen many such repairs fail because the welding procedure was not suitable for the corrosive environment. The most common cause of failure is the selection of the wrong consumable. If the consumable does not have the same or better corrosion resistance than the base metal, the repaired area will corrode preferentially, leading to premature failure.

Another common issue is the presence of cracks in the base metal. The impeller may have cracks that are not visible on the surface. If these cracks are not removed before welding, they will propagate through the repair. In my experience, the impeller should be inspected for cracks using a non-destructive testing method, such as dye penetrant or magnetic particle testing, before the repair is started. The paper does not mention this, but it is an important step in the repair procedure.

Key Questions and Reflections

The paper does not provide a detailed cost analysis, but it is clear that the repair was economically justified. The plant saved the cost of a new impeller and the associated downtime. However, the paper also raises the question of the remaining life of the repaired impeller. A repair can extend the life of a component, but it does not make it new. The repaired area may have a different microstructure and different properties than the original material. In my experience, a well-executed repair can extend the life of a pump impeller by several years, but it requires careful monitoring and inspection.

Another question is the qualification of the welding procedure. In a salt mine, the welding is often performed by the plant's own maintenance staff. These welders may not have the same level of certification as those in a fabrication shop. The paper does not mention any qualification requirements, but in my experience, it is essential to qualify the welding procedure and the welders before performing a critical repair. This ensures that the repair will meet the required quality standards.

Study Insights and Implications

The paper is a practical case study that demonstrates the value of surfacing repair for components in a corrosive environment. It reinforces the principle that a well-planned and executed repair can be a cost-effective alternative to replacement. For a plant engineer, the lesson is to develop a repair procedure, train the maintenance staff, and have the necessary consumables and equipment on hand. The paper also highlights the importance of material selection and process control. A repair is only as good as the material and the welding technique used to perform it. The paper is a useful reference for anyone involved in the maintenance of pumps and similar equipment in corrosive environments.