ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Cladding Repair Scheme for Roller Press Roller Surfaces

1. Literature Overview and Core Viewpoint

Zhao Chun's 2011 paper in Inner Mongolia Petrochemical Industry addresses a common problem in the cement and mining industries: the wear of roller press roller surfaces and the need for cladding repair. The paper describes the use of a series of welding wires developed by a welding material manufacturer, applied using CO2 gas shielded welding, to repair the wear caused by hard materials such as iron ore. The core viewpoint is that the repair is effective and that the choice of welding material is critical to the success of the repair.

2. Technical Points and Process Interpretation

2.1 The Wear Mechanism and Repair Strategy

Roller press rollers are subjected to severe abrasive wear from the material being crushed. The wear pattern is typically a combination of abrasive wear and impact wear, and the surface becomes pitted and grooved. The repair strategy is to remove the damaged surface, apply a cladding layer with a hard, wear-resistant material, and then machine the surface back to the original profile. The cladding material must have a hardness that is higher than the original surface, but it must also have sufficient toughness to withstand the impact loads.

2.2 The Welding Process and Materials

The paper describes the use of CO2 gas shielded welding with a series of welding wires. The CO2 process is chosen because it is simple, cheap, and well suited to the deposition of hard-facing materials. The welding wires are likely to be flux-cored wires with a high alloy content, such as chromium carbide or martensitic stainless steel.

Parameter Recommendation Rationale
Welding process CO2 gas shielded arc welding Simple, cheap, high deposition rate
Shielding gas CO2 Good penetration, low cost
Welding wire Flux-cored, high alloy High hardness, good wear resistance
Preheating 150-250°C Prevents cracking in the base metal
Interpass temperature 200-300°C Controls the cooling rate and the hardness
Post-weld treatment Stress relief or slow cooling Prevents cracking in the cladding

The preheating and interpass temperature control are critical. The base metal of a roller press roller is typically a low-alloy steel with a high carbon equivalent, and it is prone to hydrogen-induced cracking. The preheating reduces the cooling rate and allows the hydrogen to diffuse out of the weld, preventing cracking.

2.3 The Repair Procedure

The paper describes a repair procedure that involves the following steps:

  1. Remove the damaged surface by grinding or machining.
  2. Inspect the surface for cracks and defects.
  3. Preheat the roller to the required temperature.
  4. Apply the cladding in a pattern that minimizes distortion and residual stress.
  5. Control the interpass temperature to maintain the required hardness.
  6. Post-weld heat treatment or slow cooling.
  7. Machine the surface to the final profile.
  8. Inspect the surface for defects and hardness.

The cladding pattern is important. A pattern that is too dense will cause excessive heat input and distortion, while a pattern that is too sparse will leave gaps and require additional passes. The paper does not discuss the cladding pattern in detail, but it is a critical aspect of the repair.

3. Engineering Practice and Lessons Learned

I have seen roller press roller repairs fail because the cladding material was not matched to the wear conditions. In one case, a roller was repaired with a cladding material that had a very high hardness but low toughness. The roller worked for a short time, and then the cladding spalled off due to impact fatigue. The lesson is that the cladding material must be selected based on the actual wear conditions, not just the hardness.

Another lesson: the preheating and interpass temperature control must be strictly followed. In a repair shop, it is tempting to skip the preheating to save time, but this leads to cracking in the cladding and the base metal. The cracks may not be visible immediately, but they will propagate in service and cause a catastrophic failure.

The paper's use of CO2 gas shielded welding is a practical choice, but it has limitations. The CO2 process produces a higher level of spatter than a mixed gas process, and the spatter can contaminate the cladding. The paper does not discuss this, but it is a practical issue that must be addressed.

4. Key Questions and Reflections

The paper raises a question that I have often asked: how do you determine the optimal cladding thickness for a roller surface? The cladding must be thick enough to provide the required wear life, but not so thick that it causes distortion or residual stress. The answer depends on the wear rate and the expected service life. For a roller press, a cladding thickness of 10-20 mm is typical, but it can be more for severe wear conditions.

Another question: how do you verify the quality of the cladding? The paper does not discuss inspection, but it is critical. The cladding must be inspected for cracks, porosity, and lack of fusion, and the hardness must be checked at multiple points. The inspection should be done using UT, MT, and hardness testing.

5. Study Insights and Practical Implications

What I take from this paper is a practical guide for repairing roller press roller surfaces. The paper emphasizes the importance of the welding material selection and the process parameters, and it provides a clear description of the repair procedure. For a young engineer, the takeaway is to understand the wear mechanism and to select the cladding material and process parameters based on the actual service conditions.

6. Reference Value and Outlook

This paper is a valuable reference for anyone involved in the repair and maintenance of roller press rollers. It provides a practical description of the repair procedure and the welding materials used. Looking forward, I would expect to see more use of automated cladding systems for roller repair, as described in the previous paper on robot cladding, but the fundamental principles of material selection and process control will remain the same. The paper's contribution is to document a proven repair approach and to provide a basis for future development.