ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Process Control of Hardfacing Repair Quality for High-Pressure Grinding Roller

Literature Overview and Core Problem

The 2011 paper by Wang Zizhou addresses the quality control of hardfacing repair for the rolls of a high-pressure grinding roll (HPGR), specifically the RP-Z170/180 model used in a cement plant. The paper emphasizes that the quality of the hardfacing repair is determined by three key factors: proper selection of the welding wire, a thorough understanding of the roll base material, and strict adherence to the designed welding procedure. The paper uses the repair of the moving roll of an RP-Z170/180 HPGR as a case study to demonstrate the importance of process control. This is a topic that I have seen many times in the field, and the paper's emphasis on process control is spot on. In my experience, most hardfacing failures are not due to the alloy itself, but to poor process control during the repair.

Technical Points and Process Interpretation

The paper's three key points are the foundation of any successful hardfacing repair. First, the selection of the welding wire must be based on the specific wear mechanism and the operating conditions of the roll. For an HPGR, the wear mechanism is a combination of abrasion and impact, so the wire must provide both hardness and toughness. A high-chromium carbide wire is a common choice, but the paper suggests that the wire must be matched to the base material. Second, the base material must be fully understood before welding. The roll is typically made of a high-carbon steel or a cast iron, which has a high carbon content and a low weldability. If the base material is not properly identified, the welding procedure may be unsuitable, leading to cracking or lack of fusion. Third, the welding procedure must be followed exactly as designed. This includes the preheat, interpass temperature, welding parameters, and post-weld treatment.

Process Control Point Key Requirement Verification Method
Wire selection Match to wear mechanism and base material Chemical analysis, hardness test.
Base material inspection Identify carbon content, alloy content Spectrometry, hardness test.
Preheat temperature 200–300 °C depending on base material Contact pyrometer or thermal crayon.
Interpass temperature Max 350 °C Contact pyrometer.
Welding parameters Current, voltage, travel speed Ammeter, voltmeter, tachometer.
Post-weld treatment Slow cooling, stress relief Temperature record.
Final inspection Hardness, crack detection, dimensional check Hardness tester, PT/MT, caliper.

The paper's case study of the RP-Z170/180 roll is a good example of how process control can make or break a repair. The roll is a large, heavy component, and the hardfacing is applied in a semi-automatic or automatic mode. The welding must be done in a continuous, uniform manner, with no interruptions, to avoid the formation of cold laps or lack of fusion. The paper reports that the repair was successful, which confirms the importance of the three key points. In my experience, the most common mistake is to skip the preheat or to use an inadequate preheat temperature. This leads to cracking in the HAZ, which can propagate into the hardfacing and cause spalling. The second most common mistake is to use a welding wire that is not suitable for the base material. For example, using a high-hardness wire on a high-carbon base material can lead to excessive dilution and cracking.

Integration with Engineering Practice and Lessons Learned

The paper's emphasis on process control is a lesson that I have learned the hard way. In one project, I was involved in the repair of a large roll for a steel mill, and the hardfacing failed within a week. The investigation revealed that the welder had not preheated the roll, despite the procedure requiring a preheat of 250 °C. The result was a crack that started in the HAZ and propagated through the hardfacing. The cost of the failed repair, including the removal of the hardfacing, the re-welding, and the downtime, was several times the cost of a properly controlled repair. This experience taught me that process control is not just a formality; it is the difference between a successful repair and a costly failure. The paper's recommendation to use a written procedure and to verify each step is the right approach.

Failure Mode Root Cause Countermeasure
HAZ cracking Insufficient preheat Increase preheat to 250 °C.
Spalling of hardfacing Dilution from base metal Use a buffer layer.
Lack of fusion Low heat input or poor technique Increase current or adjust travel speed.
Porosity Contamination or moisture Clean surface, dry electrode.
Over-tempering High interpass temperature Control interpass to max 350 °C.

The paper does not discuss the use of a buffer layer, but in my experience, it is often necessary when the base material is a high-carbon steel or a cast iron. The buffer layer, typically a nickel-based or austenitic stainless steel alloy, prevents the carbon from migrating into the hardfacing and forming brittle martensite. The paper's case study may not have required a buffer layer because the base material was a low-alloy steel, but for high-carbon base materials, the buffer layer is essential.

Key Questions and Reflections

The paper raises a question that I have often asked: how much process control is enough? The answer is that it depends on the criticality of the component and the consequences of failure. For an HPGR roll, the consequences of failure are severe: the roll must be replaced, which can take days, and the lost production is significant. Therefore, the process control must be rigorous. The paper's three key points are a good starting point, but I would add a fourth: the qualification of the welder. The welder must be qualified for the specific hardfacing procedure, and the qualification must be documented. In many shops, the welder is qualified for general welding, but not for hardfacing, which is a specialized process that requires a different set of skills.

Study Insights and Outlook

This paper is a valuable reminder that hardfacing is not a simple repair job; it is a precision engineering process that requires the same level of control as any critical weld. The paper's emphasis on wire selection, base material understanding, and procedure adherence is the foundation of any successful hardfacing repair. In the steel pipe industry, we use similar process control for the repair of large components such as mandrels, dies, and rolls. The lessons from this paper apply directly to those applications. I would recommend this paper to any engineer who is responsible for the repair of large, critical components, and I would add that the key to success is not just the alloy, but the discipline of the process.