ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Post-Weld Tempering Effects on Microstructure and Hardness Gradient in ZG15MnMoVCu Hardfacing Fusion Zone

Literature Overview and Study Context

This study by Xiao Xinhua and Xing Zhigang addresses a problem I have seen repeatedly on the shop floor: hardfacing repairs on cast steel components that crack, spall, or fail prematurely in service. The base material ZG15MnMoVCu is a low-alloy cast steel used in heavy machinery, and the repair route is Cr-based flux-cored wire surfacing. The authors systematically compared air cooling after welding against tempering at different temperatures, then examined the microstructure, chromium distribution across the fusion line, and microhardness gradients. This is exactly the kind of metallurgical work that should be done before a repair procedure is written into a works instruction.

Metallurgical Interpretation of the Results

The study found that direct air cooling after welding produces a problematic microstructure on both sides of the fusion line. On the base metal side, the heat-affected zone develops irregular acicular Widmanstätten ferrite, which is a sign of grain coarsening and poor toughness. On the deposit side, the Cr-based hardfacing layer shows coarse acicular martensite, which is hard but brittle and prone to hydrogen-assisted cracking. The chromium distribution across the fusion line is highly uneven, and the microhardness gradient is steep.

When tempering is applied, the picture changes progressively with increasing temperature. The acicular Widmanstätten ferrite on the base metal side gradually gives way to granular pearlite and ferrite, which is a much more balanced and ductile microstructure. The deposit transforms from coarse acicular martensite to fine lath tempered martensite, which retains hardness but gains ductility and toughness. Chromium diffusion becomes more uniform across the fusion line, and the hardness gradient flattens out.

Condition Base Metal HAZ Microstructure Deposit Microstructure Cr Distribution Hardness Gradient
As-welded + air cool Acicular Widmanstätten ferrite Coarse acicular martensite Highly uneven Steep
Low-temperature temper Mixed Widmanstätten + granular pearlite Tempered martensite, partially refined Moderately even Moderate
High-temperature temper Granular pearlite + ferrite Fine lath tempered martensite Even Shallow

Practical Implications for Repair Welding and Hardfacing

From a practical standpoint, this study confirms what I have learned the hard way on several occasions. When we hardface a cast steel component and skip post-weld heat treatment, we are gambling with the integrity of the repair. The steep hardness gradient across the fusion line creates a stress concentration site where hydrogen can accumulate and where fatigue cracks can initiate. I have seen hardfaced rolls and dies fail after only a few weeks of service because the repair was left in the as-welded condition.

The tempering temperature must be selected based on the service requirements. If the component needs maximum wear resistance, a lower tempering temperature may be acceptable, but the risk of cracking increases. If the component is subject to impact or cyclic loading, a higher tempering temperature is safer, even at the cost of some surface hardness. The study also highlights the importance of controlling the heat input and preheat temperature, because these influence the width of the HAZ and the initial grain size.

Key Lessons and Recommendations

  1. Never leave a hardfaced cast steel component in the as-welded condition if it is going into service under load. Tempering is not optional; it is a quality gate.
  2. The tempering temperature should be determined by balancing hardness requirements against toughness and cracking resistance. A two-stage temper may be necessary for large or complex components.
  3. Chromium distribution across the fusion line is a good indicator of the effectiveness of the heat treatment. If the distribution is uneven, the tempering was insufficient.
  4. Microhardness mapping across the fusion line should be part of the qualification procedure, not just a research tool. It reveals problems that average hardness values hide.
  5. Document the entire procedure — preheat, interpass temperature, tempering cycle, and cooling rate — and verify it with metallographic examination before releasing the component to service.

Concluding Reflection

This study is a reminder that welding is not just about depositing metal; it is about managing the metallurgical consequences of thermal cycling. The authors have provided a clear, quantitative picture of how tempering improves the fusion zone, and their findings should be incorporated into any repair welding procedure for ZG15MnMoVCu components. On the shop floor, we often focus on getting the weld done quickly, but the real cost is in the failures that happen later. Tempering is a small investment in time that pays back many times over in service life.