Post-Weld Tempering of Hardfaced ZG15MnMoVCu: Metallurgical Lessons from the Fusion Line
Reading the Paper as a Practitioner
Xiao Xinhua and Xing Zhigang's 2015 paper in Hot Working Technology is a classic example of the kind of metallurgical investigation that should be required reading for anyone who specifies hardfacing on cast steel components. The title is precise: the effect of post-weld tempering on the microstructure and hardness gradient across the fusion line of a hardfaced ZG15MnMoVCu casting. I have seen too many hardfaced components fail at the fusion line, and this paper explains why — and what to do about it.
The paper's experimental design is straightforward but effective. A Cr-based flux-cored wire is used to hardface a ZG15MnMoVCu substrate, and the samples are then subjected to different post-weld treatments: air cooling, and tempering at various temperatures. The analysis focuses on three things: the microstructure on both sides of the fusion line, the distribution of chromium across the fusion line, and the microhardness gradient. This is exactly the right set of measurements, because the fusion line is where failures start.
The As-Welded Condition: A Recipe for Trouble
The paper reports that in the as-welded, air-cooled condition, the base metal side near the fusion line shows an irregular acicular Widmanstätten structure, while the hardfaced layer shows coarse acicular martensite. This is a bad combination. Widmanstätten ferrite in the base metal is a sign of a high heat input and a slow cooling rate through the transformation range, and it is associated with a loss of toughness. Coarse acicular martensite in the deposit is the opposite problem: it is hard and brittle, with a high susceptibility to hydrogen-induced cracking if any moisture is present.
The paper's key observation is that the chromium distribution across the fusion line is highly non-uniform in the as-welded condition. This is the dilution effect I discussed in my note on hardfaced work rolls. The first layer of the deposit picks up carbon and manganese from the base metal, which shifts the hardenability of the deposit and changes the martensite start temperature. The result is a steep hardness gradient across the fusion line, which is exactly where residual stresses concentrate. When the component is loaded in service, the soft side and the hard side deform differently, and the interface becomes a site for crack initiation.
The Tempering Response: What the Data Shows
The paper's data on tempering is the most valuable part. As the tempering temperature increases, the Widmanstätten structure in the base metal gradually disappears and is replaced by granular pearlite and ferrite. The coarse acicular martensite in the deposit transforms into fine lath-like tempered martensite. The chromium distribution becomes more uniform across the fusion line, and the hardness gradient decreases.
This is exactly what I would expect, and it is what I would tell any engineer who asks why a hardfaced component must be tempered after welding. The tempering temperature is the critical variable. Too low, and the martensite remains brittle and the hardness gradient persists. Too high, and the deposit loses its wear resistance. The paper does not give a specific temperature, but my experience suggests a tempering range of 550–620°C for this type of Cr-based deposit, with a holding time of at least 2 hours per 25 mm of thickness.
| Condition | Base Metal Structure | Deposit Structure | Cr Distribution Across Fusion Line | Hardness Gradient |
|---|---|---|---|---|
| As-welded, air cooled | Acicular Widmanstätten | Coarse acicular martensite | Highly non-uniform | Steep |
| Tempered at low temperature | Widmanstätten partially retained | Tempered martensite, some acicular | Moderately non-uniform | Moderate |
| Tempered at high temperature | Granular pearlite + ferrite | Fine lath tempered martensite | Uniform | Shallow |
The Practical Implication: Tempering Is Not Optional
The paper's conclusion is clear: post-weld tempering is essential for hardfaced ZG15MnMoVCu components. This is not a recommendation — it is a requirement. In my experience, the most common cause of hardfaced component failure is the decision to skip tempering because the component "looks fine" after welding. It does not look fine. It looks fine because the surface is hard and shiny, but the subsurface is a trap for hydrogen and a site for stress concentration.
The paper also raises an important point about the base metal. ZG15MnMoVCu is a cast steel with a relatively high carbon content (0.15% nominal, but castings often run higher). This makes it susceptible to cold cracking in the HAZ, especially if the preheat is inadequate. The paper does not discuss preheat, but I would specify a preheat of 150–200°C for this material, and I would insist on a post-weld hydrogen removal treatment before the final temper.
What I Would Tell the Shop Floor
If I were standing in front of a welder who is about to hardface a ZG15MnMoVCu casting, I would give him three instructions. First, preheat the component to at least 150°C and maintain that temperature throughout the welding operation. Second, use a low heat input — not because it makes the weld look better, but because it reduces the width of the HAZ and limits the extent of the Widmanstätten structure. Third, do not remove the component from the welding station until it has been tempered. If the tempering furnace is not available, wrap the component in thermal blankets and let it cool slowly to room temperature before any further processing.
The paper's contribution is that it gives the metallurgical reason behind these instructions. The Widmanstätten structure is not just a cosmetic defect — it is a sign that the base metal has been overheated and has lost its toughness. The coarse martensite in the deposit is a sign that the deposit is too hard and too brittle. The chromium gradient is a sign that the deposit is not homogeneous and will not behave as a single material. All three problems are solved by tempering, but only if the tempering is done at the right temperature and for the right time.
The Bigger Picture: Why This Paper Is a Model
This paper is a model of what a hardfacing investigation should look like. It does not just report that the hardness is high or low — it explains why, by looking at the microstructure and the element distribution. It does not just recommend a treatment — it shows the effect of the treatment on the properties that matter. And it does not ignore the fusion line, which is the most critical region in any hardfaced component.
The lesson for the industry is that hardfacing is not a simple process. It is a metallurgical operation that requires control of heat input, dilution, preheat, and post-weld treatment. The paper shows what happens when that control is missing, and it shows what happens when it is applied. The difference is the difference between a component that lasts a year and a component that lasts a week.
Zhuojin Pipe Fitting Co., Ltd