Multi-Directional Seismic Performance Evaluation of Concrete-Filled Steel Tube Pier-Continuous Beam Bridge Based on Time-History Analysis
1. Literature Overview and Core Contribution
This study addresses a critical issue in bridge engineering: the seismic performance of concrete-filled steel tube (CFST) piers in continuous beam bridges under multi-directional earthquake loading. CFST piers are widely used in high-speed railway and highway bridges in China because they offer high load-carrying capacity, excellent ductility, and fast construction. However, most existing studies have focused on single-directional loading, which does not represent the real behaviour of a bridge pier under a three-dimensional earthquake. The study uses the time-history analysis method with actual earthquake records to evaluate the response of a CFST pier-continuous beam bridge under multi-directional seismic excitation. The key contribution is the development of a comprehensive evaluation framework that considers the interaction between the pier, the beam, and the bearings.
2. Bridge Model and Analysis Parameters
The study used a typical three-span continuous beam bridge with a total length of 90 m (30 m + 30 m + 30 m). The piers were CFST columns with a diameter of 1.2 m, wall thickness of 20 mm, and concrete strength of C50. The steel tube was Q345. The bridge deck was a prestressed concrete box girder. The analysis was performed using a finite element model with fibre elements for the CFST piers and beam elements for the deck. The earthquake input was a set of three-component ground motions (two horizontal and one vertical) from actual records, including the El Centro, Kobe, and Wenchuan earthquakes. The analysis parameters are summarised below.
| Parameter | Value | Remark |
|---|---|---|
| Pier diameter | 1200 mm | CFST |
| Tube wall thickness | 20 mm | Q345 |
| Concrete grade | C50 | |
| Pier height | 8 m | |
| Span length | 30 m × 3 | Continuous beam |
| Earthquake records | El Centro, Kobe, Wenchuan | Three-component |
| Analysis method | Time-history | Direct integration |
| Damping ratio | 5% | Rayleigh damping |
3. Key Findings and Interpretation
The study found that multi-directional loading significantly affects the seismic response of the bridge. The key findings are as follows. First, the vertical component of the earthquake has a non-negligible effect on the axial force in the CFST pier, which in turn affects the bending moment capacity due to the P-M interaction. Second, the bidirectional horizontal loading causes a biaxial bending effect that reduces the flexural capacity of the pier by approximately 15–20% compared to unidirectional loading. Third, the pier displacement demand under multi-directional loading is larger than under single-directional loading, and the difference increases with the intensity of the ground motion. Fourth, the CFST pier exhibits excellent ductility, with a displacement ductility factor of 4–6, which is higher than the typical value of 3 for reinforced concrete piers.
| Loading direction | Maximum pier displacement (mm) | Ductility factor | Damage state |
|---|---|---|---|
| Unidirectional X | 120 | 4.2 | Moderate |
| Unidirectional Y | 115 | 4.0 | Moderate |
| Bidirectional X + Y | 145 | 5.1 | Moderate |
| Tri-directional X + Y + Z | 160 | 5.5 | Severe |
4. Comparison with Code Requirements and Design Implications
The study compares the results with the requirements of JTG/T 2231-01 (Guidelines for Seismic Design of Highway Bridges). The code requires a displacement ductility factor of at least 3.0 for the elastic response, and 4.0 for the plastic response. The CFST pier in this study achieved a ductility factor of 5.5 under tri-directional loading, which is above the code requirement. However, the study also found that the damage state under tri-directional loading was "severe," meaning that the concrete in the core was crushed and the steel tube had local buckling. This indicates that the code's ductility requirement may not be sufficient to ensure the repairability of the bridge after a major earthquake. The study recommends that the design of CFST piers should consider the vertical component of the earthquake, and that the P-M interaction should be explicitly checked.
5. Engineering Practice and Lessons from the Field
From my experience in the steel pipe industry, I can say that CFST piers are a demanding application for steel pipe. The pipe must have excellent weld quality, especially the longitudinal seam, because it is subjected to high axial forces and bending moments. The pipe must also have good dimensional accuracy—an ovality of more than 1% can cause local buckling at a lower load. The concrete filling process is critical: the concrete must be placed without voids, and the interface between the steel tube and the concrete must be free of gaps. In practice, I have seen problems with concrete filling: voids at the top of the pier, insufficient compaction, and shrinkage gaps. These defects can significantly reduce the load-carrying capacity and the ductility of the CFST pier. The study's finding that the damage state was "severe" under tri-directional loading is a warning that the quality of the concrete filling must be strictly controlled.
6. Key Questions and Reflections
The study raises a critical question about the definition of "severe damage" and the repairability of the bridge. In the test, the steel tube had local buckling, which is a serious damage state. However, the study does not address the post-earthquake repair procedure. In practice, a CFST pier with local buckling is very difficult to repair—the concrete is crushed, and the steel tube has permanent deformation. The repair would require replacing the entire pier or strengthening it with external steel plates. This is a significant cost and a long downtime. I would recommend that the design of CFST piers include a damage control criterion that limits the local buckling of the steel tube to a level that can be repaired. This would require a higher wall thickness or a higher steel grade.
7. Study Insights and Practical Recommendations
This study is a valuable contribution to the seismic design of CFST bridges. The key insight is that multi-directional loading must be considered, and the vertical component of the earthquake cannot be ignored. For the steel pipe industry, this study reinforces the importance of pipe quality: the steel tube in a CFST pier is not just a formwork for concrete, it is a structural element that must have excellent mechanical properties, weld quality, and dimensional accuracy. I would recommend the following: (1) for CFST pier pipes, require a full-length UT of the longitudinal seam and a hydrostatic test; (2) specify a maximum ovality of 0.5% and a maximum wall thickness tolerance of ±5%; (3) require a residual stress measurement on the first article to ensure that the pipe does not have excessive residual stress that could cause local buckling; (4) for the construction site, ensure that the concrete filling is monitored by ultrasonic testing or other non-destructive methods to detect voids; (5) for the design office, include the vertical component of the earthquake in the analysis and check the P-M interaction explicitly. This study provides the technical basis for these recommendations.
Zhuojin Pipe Fitting Co., Ltd