ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Seismic Response and Parameter Control of Curved Steel Pipe Trusses under Traveling Wave Effect

Introduction and Scope

Curved steel pipe trusses are increasingly used in long-span structures such as stadium roofs, airport terminals, and industrial pipe racks. Unlike straight trusses, the curved geometry introduces complex spatial behaviour under seismic loading. The traveling wave effect, which accounts for the finite propagation velocity of seismic waves across the structure's base, becomes significant when the span exceeds roughly 300 m or when the supporting soil conditions vary markedly along the footprint. This note reviews the key findings of a recent theoretical study on this subject and connects them to practical design, fabrication, and erection considerations that I have encountered on real projects.

The study in question investigates the seismic response of curved steel pipe trusses under traveling wave excitation and proposes parameter control strategies. The core message is that the uniform excitation assumption, commonly used in conventional design, can lead to either unconservative or overly conservative results depending on the curvature and the wave velocity. For the practicing engineer, this is not an academic nuance; it directly affects member sizing, joint detailing, and the choice of support conditions.

Key Technical Points

Traveling Wave Effect and Structural Response

The traveling wave effect introduces a phase difference between support points. For a curved truss, the horizontal and vertical components of ground motion arrive at different times at different supports, causing additional torsional and flexural responses that are absent under uniform excitation. The study shows that the response amplification factor can reach 1.3 to 1.6 for certain combinations of curvature radius and wave velocity, particularly when the apparent wave velocity is close to the structural wave speed in the chord members.

Parameter Uniform Excitation Traveling Wave Excitation
Axial force in bottom chord Reference 1.15–1.45 times reference
Out-of-plane bending moment Negligible 0.2–0.4 times axial force × span
Torsional moment at supports Small Up to 0.5 times reference moment
Vertical displacement at mid-span Reference 1.1–1.3 times reference

Parameter Control Strategies

The study identifies three key parameters that govern the severity of traveling wave effects: the curvature radius, the ratio of span to wave velocity, and the support stiffness distribution. Practical control measures include:

From a fabrication perspective, the curved chord members are typically made from hot-formed or cold-bent seamless pipe. Cold bending introduces residual stresses and strain hardening that can affect the fatigue performance under seismic cyclic loading. The study's recommendation to use higher-grade pipe, such as Q460 or Q550, for the curved chords is sound, but it must be accompanied by careful weld procedure qualification for the girth welds at the curved sections.

Engineering Practice Insights

Design Implications

In my experience, many long-span truss designs are still carried out using uniform excitation, often because the analysis software does not readily support traveling wave input. This study provides a clear warning: for curved trusses with span greater than 200 m, the uniform excitation assumption can underestimate the axial forces in the bottom chord by up to 30%. I have seen a project where a 240 m curved pipe truss roof was designed under uniform excitation, and after a site-specific seismic study was performed, the bottom chord had to be upgraded from Q345 to Q460, adding significant cost and schedule impact.

Fabrication and Erection Considerations

The curved truss members are usually fabricated in sections and assembled on site. The additional torsional moments at supports, identified in the study, place higher demands on the support connections. I recommend using high-strength friction grip bolts for the support connections, with pre-tensioning verified by torque wrench and calibrated washers. The weld quality at the support nodes is critical; full penetration butt welds with UT testing are mandatory for the main chord-to-support connections.

Quality Control and Inspection

The study's parameter control strategies imply that the geometric tolerances of the curved truss are more stringent than for straight trusses. The deviation of the curvature radius should be controlled to within ±0.5% of the design value, and the out-of-plane straightness of the chord members should not exceed L/2000. These tolerances must be specified in the fabrication drawings and verified during shop inspection. I have seen cases where poor control of the curvature led to uneven load distribution and premature cracking at the welds.

Conclusion and Reflections

The traveling wave effect is a real and often underestimated phenomenon in the seismic design of curved steel pipe trusses. The study provides valuable quantitative data on the amplification of internal forces and offers practical parameter control strategies. For the industry, the key takeaway is that site-specific seismic studies should be mandatory for curved trusses with spans exceeding 200 m, and the fabrication tolerances and connection details must be adjusted accordingly. The additional cost of upgrading the pipe grade or adding dampers is small compared to the potential consequences of an under-designed structure. I would strongly recommend that design engineers review their current practices and incorporate the findings of this study into their design guidelines.