ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Tie-Constrained Square Steel Tube Ultra-High Strength Concrete Columns: Axial Compression and the Welding of Ties

Overview of the Research

The paper on tie-constrained square steel tube ultra-high strength concrete columns addresses a column system where the steel tube is reinforced with external ties to improve the confinement of the concrete core. The ties are welded to the tube wall, and they act as external stirrups that prevent the tube from expanding laterally under axial load. This is a practical solution for columns that must carry very high axial loads, and it is a direct application of our product. The key question from a pipe maker's perspective is whether the tie-to-tube weld can be made reliably and whether the tube wall can withstand the local stress concentration at the tie location.

Technical Points That Matter on the Shop Floor

The square steel tube in this system is typically manufactured by cold-forming from a plate or by roll-forming from a coil. The corners of the tube have a residual stress distribution that is different from the flat walls, and this residual stress affects the local buckling behaviour of the tube under axial load. The ties are welded to the tube wall at regular intervals, and each weld creates a heat-affected zone (HAZ) that has a lower yield strength than the base metal. If the ties are too close together, the HAZs overlap, and the tube wall becomes a series of soft zones that may yield prematurely.

The tie spacing is a critical parameter. In our experience, the tie spacing should be no less than 100 mm and no more than 200 mm for a tube with a wall thickness of 8 to 12 mm. If the spacing is too small, the welding heat input accumulates and the tube wall distorts. If the spacing is too large, the confinement effect is lost, and the concrete core expands laterally without restraint. The paper likely provides a formula for the optimum spacing, but the formula must be validated with the actual tube dimensions and the welding process used.

The tie itself is typically a round bar or a flat bar, and it is welded to the tube wall with a fillet weld. The weld size must be at least 0.7 times the tie diameter, and the weld must be continuous around the tie. A discontinuous weld will create a notch at the tie end, and this notch will initiate a crack under cyclic loading. We have seen this failure mode in a bridge pier, where the tie weld was intermittent, and the tie detached from the tube, causing a loss of confinement and a sudden collapse of the column.

Manufacturing and Quality Control Considerations

The fabrication of a tie-constrained column is a multi-step process. The tube is manufactured first, then the ties are welded to the tube wall, and then the concrete is placed inside. The tube must be straight and square, with a tolerance of plus or minus 2 mm on the outside dimension and plus or minus 1 mm on the wall thickness. If the tube is out of square, the ties will not align with the tube wall, and the weld will be either oversized or undersized.

The welding of the ties is a manual process, and it requires a skilled welder who can maintain a consistent heat input. The weld should be made with GMAW or FCAW, using a 1.2 mm diameter wire and a current of 160 to 200 amps. The heat input should be limited to 1.0 to 1.4 kJ/mm to avoid excessive distortion of the tube wall. The tube wall is thin, and a high heat input will cause the wall to bow outward, which reduces the confinement effect.

The tie-to-tube weld should be inspected with MT or PT, and the inspection should cover the full length of the weld. A visual inspection is not sufficient because the weld may have a lack of fusion at the root, which is not visible from the surface. We have had cases where a tie weld passed visual inspection but failed under load because the root was not fused. This is a common defect in fillet welds, and it is caused by an incorrect welding angle or a dirty surface.

Integration with Engineering Practice

In a real project, the tie-constrained column is fabricated in a shop and shipped to site in lengths of 6 to 12 meters. The ties must be protected during transport, and the tie welds should be inspected before shipping. We have had cases where a contractor shipped the column without protecting the ties, and the ties were bent during loading and unloading. The bent ties could not be straightened without damaging the weld, and the column had to be returned to the shop for repair.

The concrete placement is a critical step. The concrete must be placed in layers of no more than 500 mm, and each layer must be vibrated to remove air pockets. If the concrete is placed too quickly, the air pockets will form at the tie locations, and the confinement effect will be reduced. The concrete must be a high-strength mix with a water-to-cement ratio of no more than 0.35, and it must have a slump of 150 to 200 mm to ensure that it flows around the ties.

The column must be cured for at least 28 days before it is loaded, and the curing temperature must be maintained at 20 to 25 degrees Celsius. If the curing temperature is too low, the concrete strength will not develop fully, and the column will fail at a load that is lower than the design load. We have seen this in a project where the column was cast in winter and the curing temperature was 5 degrees Celsius, resulting in a concrete strength of only 60% of the design strength.

Key Questions and Reflections

The research raises a question about the interaction between the tie weld and the tube wall. The weld creates a HAZ that has a lower yield strength than the base metal, and this HAZ may become the location of the first yield under axial load. If the HAZ yields before the concrete reaches its peak strength, the confinement effect is lost, and the column fails prematurely. The paper likely addresses this by recommending a minimum tube wall thickness, but the recommendation must be based on the actual welding process and the heat input used.

The research also raises a question about the tie spacing and the tie diameter. A larger tie diameter provides more confinement, but it also creates a larger HAZ and a larger stress concentration. The optimum tie diameter is a balance between confinement and stress concentration, and it must be determined by testing, not by calculation alone. In our experience, a tie diameter of 10 to 12 mm is a good starting point for a tube with a wall thickness of 8 to 10 mm, but the final selection must be validated with a full-scale test.

Study Insights and Practical Implications

The most important lesson from this research is that the tie weld is a structural weld, not a tack weld. It must be made by a qualified welder, inspected with MT or PT, and tested with a bend test on a sample joint. The cost of a tie weld is small compared to the cost of the column, and the cost of a failure is enormous. I would therefore specify a minimum weld size of 8 mm for a 12 mm tie, and I would require a 100% inspection of all tie welds.

The paper also reminds us that the tube wall is a load-bearing element, and it must be manufactured to a tight tolerance. A tube that is out of tolerance by 2 mm in wall thickness may not fail in the test, but it may fail in the field under a different loading history. The cost of a tube is small compared to the cost of the column, and the cost of a failure is enormous. I would therefore specify a tighter tolerance on the tube wall thickness, say plus or minus 5% instead of the standard plus or minus 10%, and I would require a mill test certificate for every heat, not just every batch.

Reference Value and Outlook

This research is valuable because it provides a basis for designing a tie-constrained column that can carry very high axial loads. However, the results are limited to the specific tube dimensions and tie configuration used in the test. In practice, the tube may range from 200 to 500 mm in outside dimension, and the tie spacing may range from 100 to 300 mm. The design equations must be validated across this range, and the manufacturing tolerances must be tightened to ensure that the actual behaviour matches the predicted behaviour.

I would recommend that the next phase of research include a parametric study on the tie spacing and the tie diameter, and that the results be compared with a full-scale test on a column that is fabricated under shop conditions, not laboratory conditions. The difference between shop and laboratory fabrication is significant, and it is the shop conditions that determine the real performance of the column.

Summary

The tie-constrained square steel tube ultra-high strength concrete column is a practical solution for high axial loads, but its performance depends on the quality of the tie weld and the tube wall. The tie weld must be continuous, full penetration, and inspected with MT or PT. The tube wall must be manufactured to a tight tolerance, and the concrete must be placed and cured properly. These are simple requirements, but they are often overlooked in the rush to meet a schedule. The cost of compliance is small, and the cost of non-compliance is a column that fails under axial load. In my thirty years in this industry, I have seen too many projects where the tie weld was treated as a tack weld, and the result was a column that did not perform as designed. This research is a reminder that the tie weld is a structural weld, and it must be treated with the same care as any other structural weld in the building.