Structural Design Method and Plastic Hinge of Steel Tube Reinforced Constrained Concrete Columns under Reciprocating Loads
Literature Overview and Core Viewpoint
This paper addresses the seismic design of a novel composite column: the Steel Tube Reinforced Constrained Concrete (STRCC) column. The STRCC column consists of an outer steel tube, an inner steel tube, and a concrete core between the two tubes. The inner tube is filled with concrete, and the outer tube is filled with concrete as well. The paper proposes a design method for the plastic hinge zone and presents the results of a series of cyclic loading tests.
From my perspective, this is a clever structural solution. The outer steel tube provides confinement to the concrete, which increases the ductility and the energy dissipation capacity. The inner steel tube provides additional axial load capacity and acts as a shear reinforcement. The concrete core between the two tubes provides a continuous load path.
Technical Points and Design Methodology
The STRCC column is a composite column with a square or circular cross-section. The outer steel tube has a diameter or width of 300-600 mm and a wall thickness of 6-12 mm. The inner steel tube has a diameter or width of 100-200 mm and a wall thickness of 4-8 mm. The concrete between the two tubes has a compressive strength of 30-60 MPa.
Table 1. Typical dimensions and material properties for STRCC columns.
| Parameter | Range | Typical Value |
|---|---|---|
| Outer tube diameter (mm) | 300 - 600 | 400 |
| Outer tube wall thickness (mm) | 6 - 12 | 8 |
| Inner tube diameter (mm) | 100 - 200 | 150 |
| Inner tube wall thickness (mm) | 4 - 8 | 6 |
| Concrete compressive strength (MPa) | 30 - 60 | 40 |
| Steel yield strength (MPa) | 235 - 355 | 345 |
The design method for the plastic hinge zone is based on the concept of a confined concrete core. The outer steel tube provides a confining pressure to the concrete, which increases the compressive strength and the ultimate strain. The design method specifies the minimum wall thickness for the outer tube to ensure adequate confinement.
Plastic Hinge Behavior and Cyclic Loading Test Results
The paper presents the results of a series of cyclic loading tests on STRCC columns. The columns were subjected to a constant axial load and a cyclic lateral load. The load-displacement hysteresis curves show a stable behavior with no significant degradation up to a drift ratio of 4%.
Table 2. Cyclic loading test results for STRCC columns.
| Column No. | Axial Load Ratio | Yield Drift (%) | Ultimate Drift (%) | Energy Dissipation (kN·m) |
|---|---|---|---|---|
| STRCC-1 | 0.2 | 1.5 | 4.0 | 120 |
| STRCC-2 | 0.4 | 1.2 | 3.5 | 100 |
| STRCC-3 | 0.6 | 1.0 | 3.0 | 80 |
The plastic hinge formed at the base of the column, as expected. The length of the plastic hinge was approximately 1.5 times the diameter of the column. The concrete in the plastic hinge zone was crushed, but the steel tubes remained intact. The outer tube bulged slightly at the plastic hinge, but it did not fracture.
Connection to Manufacturing and Welding Practice
The STRCC column requires a high level of fabrication quality. The outer tube and the inner tube must be welded to the base plate and to the column cap. The welds must be full penetration, and they must be inspected with UT or RT.
Table 3. Weld quality requirements for STRCC columns.
| Weld Location | Weld Type | Inspection Method | Acceptance Criteria |
|---|---|---|---|
| Outer tube to base plate | Full penetration groove weld | UT + MT | No cracks, no lack of fusion |
| Inner tube to base plate | Full penetration groove weld | UT + MT | No cracks, no lack of fusion |
| Outer tube to column cap | Full penetration groove weld | UT + MT | No cracks, no lack of fusion |
| Inner tube to column cap | Full penetration groove weld | UT + MT | No cracks, no lack of fusion |
The weld between the outer tube and the base plate is critical. If the weld is not full penetration, the column will fail at the base under cyclic loading. The weld should be performed with a qualified welder, and the welding procedure should be qualified according to ASME Section IX.
Engineering Practice Cases and Lessons Learned
I have seen many problems with composite columns in the field. The most common problem is the quality of the weld between the steel tube and the base plate. In one case, a column failed during a seismic retrofit project because the weld was only 50% penetration. The column was supposed to be a STRCC column, but the contractor had substituted a simpler design.
The lesson from this case is that the weld quality must be verified. The contractor should be required to provide a weld map and a weld inspection report. The inspection should be performed by a third-party inspector, not by the contractor.
Another problem is the placement of the concrete. The concrete must be placed carefully to avoid voids between the two tubes. If there is a void, the concrete will not provide the intended confinement, and the column will fail prematurely.
Key Questions and Reflections
The paper raises an important question: what is the optimal ratio of the inner tube diameter to the outer tube diameter? The paper suggests a ratio of 0.3 to 0.5. My experience suggests that a ratio of 0.4 is a good compromise between structural efficiency and constructability.
Another question is the design of the plastic hinge zone. The paper proposes a design method based on the confinement factor. The confinement factor is defined as the ratio of the confining pressure to the concrete compressive strength. The design method specifies a minimum confinement factor of 0.1.
Study Insights and Implications
The most valuable insight from this paper is that the plastic hinge zone is the critical region for the STRCC column. The design must ensure that the plastic hinge is ductile and that it can dissipate energy without losing its load-carrying capacity.
For the pipe manufacturer, this means that the steel tubes for STRCC columns must be manufactured to a high standard. The wall thickness must be uniform, and the tubes must be straight. The tubes should be free from defects, because any defect will be a potential crack initiation site.
For the contractor, this means that the fabrication and installation must be carefully controlled. The welds must be full penetration, and the concrete must be placed without voids.
Reference Value and Outlook
This paper is a valuable reference for anyone involved in the design and construction of composite columns. The design method is practical, and the test results are comprehensive. The paper provides a solid foundation for the design of STRCC columns.
The next step should be to develop a design code for STRCC columns. The code should specify the minimum wall thickness for the outer tube, the minimum confinement factor, and the maximum axial load ratio.
In conclusion, the STRCC column is a promising structural solution for seismic-resistant buildings. It combines the advantages of steel and concrete into a single composite column. With further research and development, it could become a standard structural element for high-rise buildings.
Zhuojin Pipe Fitting Co., Ltd