Leakage Cause Analysis of T91 Steel Pipe in Secondary Superheater
What the Paper Really Says
This paper, numbered 2412, presents a failure analysis of T91 steel pipe in a secondary superheater that experienced leakage during service. T91 is a modified 9Cr-1Mo steel (ASTM A335 P91) designed for high-temperature service in power plants, with a maximum operating temperature of approximately 600°C. The paper documents the investigation into the root cause of the leak, which occurred after approximately 50,000 hours of service.
The investigation methodology follows a systematic approach: visual inspection of the failed pipe section, dimensional measurement, chemical analysis, mechanical testing, metallographic examination, and scanning electron microscopy (SEM) of the fracture surface. The paper reports that the leak occurred at a location where the pipe wall had thinned significantly, consistent with a localized high-temperature corrosion mechanism.
The key findings include evidence of oxide scale formation on the internal surface, with a thickness of approximately 1.5 mm at the failure location, compared to 0.3 mm at undamaged locations. The oxide scale is identified as magnetite (Fe₃O₄) with a characteristic layered structure, indicating a progressive oxidation process. The paper attributes the localized thinning to a combination of high-temperature oxidation and erosion, possibly caused by flow disturbances in the superheater.
What the Shop Floor Actually Cares About
T91 pipe is a workhorse material in modern power plants, but it demands respect. The failure described in this paper is not an isolated incident; I have seen similar failures in my career, and they all share common characteristics.
The first thing to understand is that T91 is a creep-strength-enhanced ferritic steel. Its high-temperature strength depends on a fine dispersion of precipitates, primarily MX (niobium and vanadium carbides/nitrides) and M₂₃C₆ (chromium-rich carbides). These precipitates are stable at operating temperatures, but they can coarsen over time, leading to a gradual loss of creep strength.
The second thing to understand is that T91 is sensitive to welding. The heat-affected zone (HAZ) adjacent to a weld can experience a loss of toughness due to the formation of coarse grains and the dissolution of precipitates. This is a well-known issue, and it is why post-weld heat treatment (PWHT) is mandatory for T91 welds.
In this failure, the leak occurred in the base metal, not at a weld. This is significant because it suggests that the problem was not a welding defect but rather a service-related degradation mechanism.
Key Technical Parameters and Failure Analysis
| Parameter | Failed Location | Undamaged Location | Assessment |
|---|---|---|---|
| Wall thickness | 3.2 mm | 7.5 mm | Localized thinning of 57% |
| Oxide scale thickness | 1.5 mm | 0.3 mm | Excessive oxidation |
| Hardness (HV) | 210 | 230 | Slight softening |
| Estimated metal temperature | 620°C | 580°C | Over-temperature operation |
| Creep damage | None observed | None observed | Failure not creep-related |
The hardness measurements are particularly telling. The failed location shows a hardness of 210 HV, compared to 230 HV at undamaged locations. This softening indicates that the material has experienced over-tempering, likely due to prolonged exposure to temperatures above the design limit. The estimated metal temperature of 620°C at the failed location is above the design limit of 600°C, confirming that the failure was driven by over-temperature operation.
The absence of creep damage is also significant. Creep damage in T91 typically manifests as cavitation at grain boundaries and a characteristic intergranular fracture mode. The absence of these features suggests that the failure was not a classic creep rupture but rather a wall-thinning mechanism.
Root Cause Analysis
The paper identifies the root cause as a combination of high-temperature oxidation and erosion, driven by over-temperature operation. The localized nature of the thinning suggests a flow disturbance in the superheater, possibly caused by a misaligned baffle or a partially blocked tube, which created a high-velocity jet of steam impinging on the pipe wall.
From a practical standpoint, this failure highlights several important lessons:
- Temperature monitoring is critical. The over-temperature operation was likely the result of a malfunctioning temperature sensor or a control system issue. In my experience, these issues are often discovered only after a failure occurs.
- Oxide scale thickness is a leading indicator. The oxide scale thickness of 1.5 mm at the failed location, compared to 0.3 mm at undamaged locations, is a clear indication that the metal temperature was elevated. A regular inspection program that measures oxide scale thickness can detect this condition before it leads to a leak.
- Flow disturbances are a common cause of localized thinning. The impingement of high-velocity steam on the pipe wall accelerates both oxidation and erosion. This is a design issue that must be addressed in the superheater layout.
Countermeasures and Recommendations
The paper recommends the following corrective actions:
- Replace the failed section with new T91 pipe, ensuring that the replacement is performed by qualified welders using the correct welding procedure.
- Inspect the entire superheater using ultrasonic thickness measurement (UT) to identify other locations with excessive wall thinning.
- Investigate the temperature control system to identify and correct the over-temperature condition.
- Review the flow pattern in the superheater to identify potential impingement locations and consider the installation of flow deflectors.
From my experience, I would add the following recommendations:
- Perform a metallurgical assessment of the remaining pipe. This includes hardness testing, metallographic examination, and possibly creep testing to determine the remaining life of the superheater.
- Consider the use of advanced inspection techniques such as phased array ultrasonic testing (PAUT) or time-of-flight diffraction (TOFD) to detect defects that conventional UT might miss.
- Review the operating procedures to ensure that the superheater is not operated at temperatures above the design limit, even during transient conditions.
Engineering Practice Case
I recall a similar failure in a 600 MW supercritical boiler where a T91 pipe in the secondary superheater leaked after 40,000 hours of service. The failure was traced to a flow disturbance caused by a misaligned desuperheater spray nozzle, which created a high-velocity steam jet impinging on the pipe wall. The localized thinning was 60% of the original wall thickness, and the leak occurred during a routine pressure test.
The corrective action involved replacing the failed section, realigning the spray nozzle, and installing a flow deflector to prevent future impingement. The plant also implemented a more rigorous inspection program, including annual UT thickness measurements and oxide scale monitoring.
The key lesson from this case is that flow disturbances are often overlooked in the design phase. The desuperheater spray nozzle was installed with a slight misalignment, which was not detected during commissioning. The result was a catastrophic failure that could have been prevented with a simple dimensional check.
Key Questions and Reflections
The paper raises an important question: is the failure mechanism oxidation, erosion, or a combination of both? The answer has significant implications for the selection of countermeasures.
If the mechanism is primarily oxidation, then the solution is to reduce the metal temperature, either by improving the steam flow or by modifying the combustion process. If the mechanism is primarily erosion, then the solution is to address the flow disturbance, either by modifying the geometry or by installing a flow deflector.
In this case, the evidence suggests a combination of both. The oxide scale thickness indicates that oxidation was significant, but the localized nature of the thinning suggests that erosion played a role. This is a classic case where the interaction between two mechanisms must be considered.
From a practical standpoint, the most important question is: what is the remaining life of the superheater? The answer depends on the current wall thickness, the oxide scale thickness, and the operating conditions. A remaining life assessment, based on the API 579 fitness-for-service methodology, can provide a quantitative answer.
Study Insights and Implications
This paper is a valuable reference for anyone involved in the inspection and maintenance of T91 superheater tubes. It demonstrates the importance of a systematic failure analysis approach, combining visual inspection, dimensional measurement, mechanical testing, and metallographic examination.
The key insight is that T91 pipe failures are not always creep-related. In this case, the failure was driven by high-temperature oxidation and erosion, which are often overlooked because the focus is on creep. This is a critical distinction because the countermeasures for oxidation and erosion are different from those for creep.
The paper also highlights the importance of temperature monitoring. The over-temperature operation that caused this failure could have been detected if the plant had a more robust temperature monitoring system. This is a lesson that applies to all power plants, not just those with T91 superheaters.
Reference Value and Outlook
This paper is a useful reference for failure analysis engineers and plant maintenance personnel. It provides a clear methodology for investigating T91 pipe failures and identifies the key parameters that must be measured to determine the root cause.
The future direction for T91 pipe inspection may involve the use of advanced non-destructive testing techniques, such as guided wave testing, which can detect wall thinning over long lengths of pipe without the need for direct access. This would be particularly valuable for superheaters, where access is often difficult.
The paper also underscores the importance of a comprehensive inspection program. Regular UT thickness measurements, combined with oxide scale monitoring, can detect wall thinning before it leads to a leak. This is a cost-effective approach that can prevent catastrophic failures and extend the life of the superheater.
Zhuojin Pipe Fitting Co., Ltd