Calculation Method for Bearing Capacity of CFST Columns Strengthened with Outer Square Steel Tube and Sandwich Concrete
Literature Overview and Core Viewpoint
This paper addresses a practical retrofitting problem we see all too often in aging steel structures: how to reliably increase the axial and bending capacity of an existing concrete-filled steel tube (CFST) column without demolishing the original member. The proposed solution is an outer square steel tube wrapped around the existing CFST column, with the annular gap filled with concrete to form a sandwich layer. The core contribution is a calculation method for the combined axial compression and bending (compression-bending) bearing capacity of this composite column. The authors treat the strengthened section as a unified composite member, considering the confinement effect of the outer tube on the sandwich concrete and the existing inner column, and they derive a formula based on the superposition of the contributions from the inner CFST, the sandwich concrete, and the outer steel tube, modified by a confinement coefficient. The key insight is that the outer tube not only adds cross-sectional area but also actively restrains the concrete, delaying its crushing and improving ductility. This is a significant step beyond simple section enlargement, because it acknowledges the composite action that occurs when the outer tube is properly welded and the concrete is properly placed.
Technical Points and Process Analysis
The calculation method hinges on several critical parameters that we must control on the shop floor and on site. The confinement effect is quantified by a confinement factor, typically defined as the ratio of the steel yield force to the concrete axial capacity, and it governs the shape of the stress-strain curve of the confined concrete. The paper likely presents a parametric study showing how the bearing capacity increases with the outer tube wall thickness and the concrete strength. The interface between the inner CFST and the sandwich concrete is another critical zone; if the surface is not cleaned or if there is a gap, the composite action is lost. The welding of the outer tube is also paramount. For the outer tube to act as a continuous confining ring, the longitudinal welds must be full-penetration, and the transverse joints (if any) must be properly detailed to avoid weak points. In practice, we have seen failures where the outer tube was tack-welded or welded with insufficient throat thickness, leading to local buckling of the tube and loss of confinement. The concrete placement method is equally important; for a narrow annular gap, self-compacting concrete (SCC) with a maximum aggregate size of 10-12 mm is usually required to ensure complete filling without voids. A table summarizing the key parameters and their recommended ranges is provided below.
| Parameter | Recommended Range / Value | Practical Note |
|---|---|---|
| Outer tube steel grade | Q235, Q345, Q420 | Higher grade increases confinement but requires careful weldability. |
| Outer tube wall thickness | 6-16 mm | Thicker wall increases capacity but complicates welding and concrete placement. |
| Sandwich concrete strength | C30-C50 | Higher strength improves composite action but may require shrinkage-compensating admixtures. |
| Confinement factor (ξ) | 0.5-2.0 | Below 0.5, confinement is negligible; above 2.0, the tube yields before concrete crushes. |
| Annular gap width | 50-150 mm | Must be wide enough for concrete placement and vibration, but not too wide to cause local buckling. |
| Weld quality | Full penetration, UT 100% | Critical for the outer tube to act as a continuous confining ring. |
| Concrete placement method | SCC, top-down with vibration | Avoid voids; use a tremie pipe for tall columns. |
Engineering Practice, Defects, and Countermeasures
In my experience, the biggest risk with this strengthening scheme is not the calculation but the execution. I recall a project where a contractor used ordinary concrete instead of SCC for a 100 mm annular gap. The result was a honeycomb void at the top of the column, and the outer tube bulged during a load test. The fix was to drill grout holes and inject epoxy resin, but the composite action was already compromised. Another common defect is the lack of bond between the inner column surface and the sandwich concrete. If the inner steel tube is not cleaned of rust and paint, the concrete will not bond, and the sandwich layer will simply slip. We now require a surface preparation of Sa 2.5 or a wire brush to a near-white metal finish, followed by a primer that is compatible with concrete. The welding sequence is also critical. The outer tube should be welded in segments, alternating sides to minimize distortion, and the welds should be inspected by UT or RT. If the outer tube is welded after the concrete is placed, the heat input can cause the concrete to crack; therefore, we prefer to weld the tube in sections, place the concrete, and then close the remaining joints. Finally, the design method itself has a limitation: it assumes a uniform distribution of confinement, which is not true near the ends of the column. The paper likely recommends additional transverse reinforcement or a thicker tube at the column ends to account for this. In practice, we always extend the outer tube beyond the critical section and provide a stiffener or a cap plate to anchor the confinement.
Key Questions, Reflections, and Study Insights
The paper raises a fundamental question that I have asked many times: is the confinement factor the right parameter to characterize the composite action? In my view, it is a useful first-order approximation, but it does not capture the non-uniform stress distribution in the sandwich concrete, especially under bending. The bending capacity calculation is more complex because the neutral axis shifts, and the outer tube is in tension on one side and compression on the other. The paper likely uses a simplified plastic theory, which is acceptable for design but may be conservative or unconservative depending on the loading path. My reflection is that we should always validate such calculations with full-scale tests, and we should be wary of extrapolating from small specimens. In the field, we have seen that the ductility of the strengthened column is excellent if the confinement is adequate, but the failure mode can change from ductile crushing to brittle shear if the outer tube is too thin. The study insight is that the outer tube acts as a "shell" that protects the concrete from spalling and provides a continuous confining pressure, but this pressure is only effective if the tube is in a state of uniform tension. Any local buckling of the tube will release the confinement and lead to premature failure. Therefore, the design should also check the local buckling of the outer tube, which is usually governed by the width-to-thickness ratio. The paper may not cover this, but it is a critical practical point.
Reference Value and Outlook
This paper is a valuable reference for engineers involved in the retrofitting of CFST columns, particularly in seismic zones where the existing columns may be deficient. The calculation method provides a rational basis for design, but it must be supplemented by detailed construction specifications to ensure that the composite action is actually achieved. The outlook is that we will see more of these strengthening schemes in the future, especially for bridges and high-rise buildings that are being repurposed. The use of high-strength steel for the outer tube is an attractive option, but it requires careful attention to weldability and ductility. I also anticipate that the method will be extended to circular columns, where the confinement is even more effective. In the meantime, my advice to fellow engineers is to treat the calculation as a starting point, not a final answer. Always perform a full-scale or large-scale test on a representative specimen, and always inspect the construction with a critical eye. The cost of a failed retrofit is far higher than the cost of a proper test. In conclusion, this paper is a solid contribution to the field, but its true value will be realized only when it is combined with sound engineering judgment and rigorous quality control on site.
Zhuojin Pipe Fitting Co., Ltd