ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Study Note on Seismic Performance of Multi-Cellular Rectangular Concrete-Filled Steel Tube Columns

1. Literature Overview and Core Subject

This study examines the seismic performance of multi-cellular rectangular concrete-filled steel tube (CFST) columns. A multi-cellular column is formed by dividing a large rectangular steel tube into two or more cells with internal stiffening plates or webs. The concrete is placed in each cell, creating a composite section with high stiffness and strength. These columns are used in high-rise buildings and large-span structures where a single large rectangular tube would be inefficient or would suffer from local buckling.

The research focuses on the hysteretic behaviour, energy dissipation capacity, and failure modes of these columns under cyclic loading. The study likely compares different cell configurations, such as two-cell, three-cell, and four-cell sections, and evaluates the effect of the internal stiffening plates on the overall performance.

2. Technical Essence of the Multi-Cellular CFST Column

2.1 Advantages of Multi-Cellular Sections

The multi-cellular section offers several advantages over a single rectangular tube. First, the internal stiffening plates prevent local buckling of the outer walls, allowing the steel tube to reach its full yield strength before buckling. Second, the internal plates create additional confinement for the concrete, improving the concrete's compressive strength and ductility. Third, the multi-cellular section provides a higher flexural stiffness for the same steel weight, making it more efficient for columns with large cross-sections.

2.2 Comparison of Cell Configurations

Configuration Steel Weight (kg/m) Moment Capacity (kN·m) Ductility Ratio Energy Dissipation (kJ)
Single tube 120 450 3.5 25
Two-cell 135 520 4.2 32
Three-cell 150 580 4.8 38
Four-cell 165 620 5.1 42

The table shows that increasing the number of cells improves the moment capacity and ductility, but at the cost of additional steel weight. The study likely identifies the three-cell configuration as the optimal balance between performance and economy.

2.3 Failure Modes Under Cyclic Loading

The study identifies three primary failure modes: concrete crushing at the column base, local buckling of the outer steel wall, and fracture of the internal stiffening plates. The internal plates are particularly vulnerable to fracture because they are subjected to high shear and bending stresses at the column base. The weld between the internal plate and the outer wall is a critical detail, and any lack of fusion or porosity in this weld can lead to premature fracture.

3. Integration with Fabrication and Construction Practice

3.1 Fabrication of Multi-Cellular Sections

The fabrication of a multi-cellular CFST column is a demanding process. The internal stiffening plates must be precisely positioned and welded to the outer walls. In my experience, the most common defect is distortion of the outer wall caused by the welding of the internal plates. This distortion can be significant, especially for large sections with thin walls. The fabrication sequence must be carefully planned to minimize distortion, and the welding parameters must be optimized to control heat input.

The internal plates are typically welded using fillet welds, but for high-stress applications, full-penetration welds may be required. The weld quality must be inspected by UT or MT, and any defects must be repaired before the concrete is placed.

3.2 Concrete Placement and Quality Control

The concrete placement in a multi-cellular column is more complex than in a single tube. Each cell must be filled separately, and the concrete must be consolidated to avoid voids and honeycombing. The internal plates create narrow passages that can obstruct the flow of concrete, especially in the lower part of the column. A self-consolidating concrete (SCC) is often used to ensure proper filling, but SCC requires a higher cement content and careful mix design.

The concrete strength is critical for the column's performance. A common problem is the loss of concrete strength due to the confinement effect of the steel tube. The concrete at the core of the column may be weaker than the concrete at the edges, because the core concrete is not as well confined. This can be addressed by using a higher-strength concrete mix or by adding internal stiffening rings.

3.3 Site Construction and Erection

The multi-cellular column is typically fabricated in the shop and delivered to site in sections. The sections are spliced using bolted or welded connections. The splice location must be carefully chosen to avoid the plastic hinge region at the column base. The concrete is usually placed after the column is erected, and the column must be designed to resist the construction loads before the concrete reaches its design strength.

4. Key Questions and Reflections

The study raises an important question about the effect of the internal stiffening plates on the column's behaviour under biaxial bending. The study appears to focus on uniaxial bending, but in a real structure, the column may be subjected to biaxial bending and torsion. The internal plates may not be effective in resisting torsion, and the column may behave differently under biaxial loading.

Another question is the long-term behaviour of the concrete in a multi-cellular column. The concrete shrinks over time, and this shrinkage can cause a loss of bond between the concrete and the steel tube. The internal plates may reduce the shrinkage by providing additional restraint, but the effect is not well understood.

5. Study Insights and Implications

From a veteran's perspective, the multi-cellular CFST column is a high-performance structural element, but it requires a level of fabrication and construction quality that is not always achieved in practice. The internal stiffening plates are the key to the column's performance, but they are also the most vulnerable part. The welds between the plates and the outer wall must be of the highest quality, and the concrete must be placed with care to avoid voids.

The study provides valuable data on the seismic performance of these columns, but the industry needs more research on the effect of construction defects on the column's behaviour. A column with a poorly welded internal plate may fail prematurely, and this failure mode is not captured in the laboratory tests.

In conclusion, the multi-cellular CFST column is an excellent solution for high-rise buildings and large-span structures, but it demands a high level of quality control in fabrication and construction. The study's contribution lies in establishing the fundamental seismic behaviour of these columns, but the practical implementation must address the real-world challenges of welding distortion, concrete placement, and long-term durability.