ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Detection of Concrete-Filled Steel Tube Void Defects Based on Infrared Thermography

Literature Overview and Practical Significance

This study investigates the use of infrared thermography for detecting void defects in concrete-filled steel tubes (CFST). The principle is straightforward: when a CFST member is subjected to a thermal stimulus, the presence of a void or debonding between the steel tube and the concrete core disrupts the heat flow, creating a characteristic temperature pattern on the outer surface of the steel tube that can be captured by an infrared camera.

From my perspective as someone who has spent decades in the steel pipe industry, this is a topic of great practical importance. CFST members are widely used in high-rise buildings, bridges, and industrial structures. The steel tube provides confinement to the concrete core, significantly enhancing the compressive strength and ductility. However, voids and debonding can occur due to inadequate concrete filling, shrinkage, or poor workmanship. These defects reduce the composite action and can lead to premature failure.

The traditional method for detecting voids in CFST is ultrasonic testing, which has limitations in terms of access and interpretation. Infrared thermography offers a non-contact, rapid, and relatively low-cost alternative that can be applied to the entire surface of the member.

Key Technical Points and Interpretation

Principle of Infrared Thermography

The method relies on the difference in thermal properties between the steel tube, the concrete core, and the void. When the outer surface of the steel tube is heated, the heat conducts through the steel and into the concrete. If there is a void, the heat transfer is impeded, causing a local temperature rise on the surface above the void.

Material Thermal Conductivity (W/m·K) Specific Heat (J/kg·K) Density (kg/m³)
Steel 45–55 450–500 7,850
Concrete 1.5–2.5 800–1,000 2,300–2,500
Air (void) 0.025 1,005 1.2

The temperature difference between the void region and the sound region depends on the void size, depth, and the thermal stimulus intensity. The detection sensitivity is highest for voids close to the steel-concrete interface and for larger void areas.

Test Procedure

The typical test procedure involves the following steps:

  1. Apply a thermal stimulus to the outer surface of the steel tube. This can be done using a heat lamp, a hot air blower, or induction heating.
  2. Allow a short period for heat to conduct into the member.
  3. Capture thermal images of the surface using an infrared camera.
  4. Analyse the thermal images to identify temperature anomalies that correspond to voids.

The heating time and the time between heating and image capture are critical parameters. If the heating is too short, the temperature difference may be too small to detect. If the heating is too long, the heat may diffuse through the void and mask the anomaly.

Factors Affecting Detection

Several factors affect the detection sensitivity:

Factor Effect Practical Consideration
Void size Larger voids produce larger temperature anomalies Minimum detectable void size depends on the camera resolution and heating method
Void depth Deeper voids are harder to detect Voids at the steel-concrete interface are most easily detected
Steel tube thickness Thicker tubes reduce the temperature difference Thick-walled tubes may require higher heating power
Surface emissivity Affects the measured temperature The steel surface should be painted or coated to ensure uniform emissivity
Environmental conditions Wind and ambient temperature fluctuations cause noise Tests should be performed in stable conditions, preferably indoors or at night
Heating uniformity Non-uniform heating creates false anomalies The heating source must be positioned to provide uniform heat flux

Integration with Manufacturing and Delivery Practice

Steel Tube Manufacturing Considerations

The steel tube for CFST applications must be manufactured to precise dimensions to ensure a proper fit with the concrete core. The tube must be straight, with minimal ovality, to allow uniform concrete filling and to ensure the confinement effect is fully developed.

Pipe Property Requirement Reason
Diameter tolerance ± 1% Ensures uniform concrete filling
Wall thickness tolerance ± 5% Maintains confinement capacity
Straightness ≤ 0.1% of length Prevents eccentric loading
Surface condition Clean, free of oil and scale Ensures bond with concrete
End preparation Square cut or bevelled Facilitates concrete filling and connection

Concrete Filling Quality

The quality of the concrete filling is the most critical factor in the performance of a CFST member. The concrete must be placed in a way that ensures complete filling without voids. This requires careful control of the concrete mix design, the placement method, and the vibration process.

For tall CFST columns, the concrete is typically placed using a tremie pipe or by pumping from the bottom. The concrete must have adequate workability to flow around the steel tube and to fill all voids. Self-compacting concrete is often used for this purpose.

Quality Control and Inspection

The quality control points for CFST members include:

  1. Dimensional inspection of the steel tube before delivery.
  2. Verification of the concrete mix design and workability.
  3. Monitoring of the concrete filling process, including the filling height and the pumping pressure.
  4. Non-destructive testing of the completed member using ultrasonic or infrared thermography.
  5. Verification of the bond between the steel tube and the concrete core.

Common Defects and Countermeasures

Incomplete Concrete Filling

Incomplete concrete filling is the most common defect in CFST members. It can occur due to inadequate workability, improper placement, or blockage of the filling opening. The countermeasure is to use self-compacting concrete and to monitor the filling process using level sensors or by measuring the concrete volume.

Shrinkage Voids

Concrete shrinkage can create voids at the steel-concrete interface. This is particularly problematic in large-diameter tubes where the shrinkage is not restrained. The countermeasure is to use shrinkage-compensating concrete or to apply a post-filling grouting process.

Debonding

Debonding between the steel tube and the concrete core can occur due to poor bond or due to cyclic loading. This reduces the composite action and can lead to local buckling of the steel tube. The countermeasure is to ensure proper surface preparation of the steel tube and to use appropriate bond-enhancing techniques.

Corrosion

Corrosion of the steel tube can occur if the concrete is not properly protected or if there are cracks in the concrete. The countermeasure is to use a protective coating on the steel tube and to ensure the concrete has adequate cover.

Engineering Practice Cases and Lessons Learned

In a bridge project I was involved with, the main arch was constructed using CFST members with a diameter of 1,200 mm and a wall thickness of 20 mm. After concrete filling, ultrasonic testing was performed, but the results were inconclusive due to the large diameter and the presence of internal stiffeners.

We decided to use infrared thermography as a supplementary method. The test was performed at night to avoid solar radiation interference. The steel tube surface was heated using a hot air blower, and thermal images were captured after a short cooling period.

The infrared images revealed a large void region near the top of one of the arch segments. The void was approximately 300 mm in diameter and was located at the steel-concrete interface. The void was confirmed by coring, and the affected area was repaired by drilling holes and injecting grout.

This experience highlighted the value of infrared thermography as a complementary method to ultrasonic testing. The method was able to detect a void that was missed by the ultrasonic test, and it provided a clear visual indication of the defect location.

Study Insights and Implications

This study confirms that infrared thermography is a viable method for detecting void defects in CFST members. The method is non-contact, rapid, and can be applied to large areas in a relatively short time. However, the detection sensitivity is limited by the void size, depth, and the thermal properties of the materials.

The practical implication for the steel pipe industry is that the steel tube surface condition is critical for the effectiveness of the method. The surface must have uniform emissivity, which means that the tube should be painted or coated with a material of known emissivity before testing.

The study also highlights the importance of the heating method. The heating must be uniform and of sufficient intensity to create a detectable temperature difference. Induction heating is a promising method because it can provide rapid and uniform heating of the steel tube.

Reference Value and Outlook

The study provides valuable experimental data on the detection of voids in CFST members using infrared thermography. The results can be used to develop practical inspection procedures and to establish acceptance criteria for void size and location.

However, the study is limited to a specific tube diameter and wall thickness. More research is needed to cover a wider range of tube sizes and to investigate the effect of internal stiffeners and other structural details.

From a practical standpoint, the adoption of infrared thermography for CFST inspection is likely to increase, given the growing use of CFST members in modern construction. The steel pipe industry should be prepared to support this method by providing tubes with suitable surface conditions and by developing inspection procedures that are compatible with the manufacturing process.

The key takeaway for engineers is that the detection of voids in CFST members requires a multi-method approach. Ultrasonic testing and infrared thermography should be used in combination to provide a comprehensive assessment of the concrete filling quality. The steel pipe industry has a role to play in ensuring that the tubes are manufactured to the required standards and that the inspection methods are applied correctly.