Eccentric Compression Behaviour of Hollow Sandwich Steel Tube Concrete Pipe Curtain Flange Bolt Connections
1. Literature Overview and Core Findings
The paper reports an experimental study on the behaviour of flange bolt connections used in a pipe curtain structure. The pipe curtain is a construction method where large-diameter steel pipes are driven horizontally to form a protective structure, and the pipes are connected end-to-end using flanges and bolts. The specific connection studied is a hollow sandwich steel tube concrete member, where the steel tube is filled with concrete, and the connection is made through a bolted flange.
From my experience with pipe connections, this is a critical detail. The flange bolt connection is the weakest link in the pipe curtain system, because it is where the load is transferred from one pipe to the next. If the connection fails, the entire structure fails. The paper's contribution is in quantifying the behaviour of this connection under eccentric compression, which is the most common loading condition in a pipe curtain.
2. Technical Interpretation: What the Connection Does
2.1 Load Transfer Mechanism
The flange bolt connection transfers load through a combination of friction and bearing. The bolts are pre-tensioned, which creates a clamping force between the two flanges. The load is then transferred by friction between the flange faces, and by bearing of the bolts against the bolt holes.
In a hollow sandwich steel tube concrete member, the load path is more complex. The concrete core carries a portion of the axial load, and the steel tube carries the rest. At the connection, the load must be transferred from the concrete core to the steel tube, and then from the steel tube to the flange. This transfer is achieved through shear connectors or through bond between the concrete and the steel.
2.2 Eccentric Loading
Eccentric loading introduces a bending moment in addition to the axial force. This bending moment causes a non-uniform stress distribution across the flange, with higher stresses on one side and lower stresses on the other. The bolts on the tension side of the connection will see an increase in load, while the bolts on the compression side will see a decrease.
The critical failure mode is likely to be either bolt yielding or flange bending. If the flange is too thin, it will bend under the eccentric load, causing the bolts to lose their pre-tension and the connection to open up. If the bolts are too small, they will yield and elongate, causing the same result.
3. Engineering Practice: What the Site Needs to Know
3.1 Bolt Pre-Tension and Tightening Procedure
The performance of the connection depends critically on the bolt pre-tension. If the bolts are not tightened to the specified pre-tension, the connection will be more flexible and will have a lower capacity. If the bolts are over-tightened, they may yield or break.
From my experience on construction sites, the most common problem with bolted connections is improper tightening. Contractors often use impact wrenches without any torque control, and they do not verify the pre-tension after tightening. This is a recipe for failure. The tightening procedure must be specified, and the pre-tension must be verified, either by torque measurement or by the turn-of-nut method.
3.2 Flange Flatness and Surface Preparation
The flange faces must be flat and parallel to ensure uniform contact. If the flanges are not flat, the load will be concentrated on the high spots, and the bolts will be unevenly loaded. The flange faces must also be free of rust, paint, and other contaminants that could reduce the friction coefficient.
In a pipe curtain, the pipes are driven horizontally, and the flanges are at the ends of the pipes. The flanges are typically welded to the pipes, and the welding can cause distortion. The flange must be machined after welding to ensure flatness, or the weld must be designed to minimise distortion.
4. Key Questions and Reflections
The paper raises several important questions:
- What is the effect of the concrete core on the connection behaviour? The concrete core is stiffer than the steel tube, so it will attract more of the axial load. This means that the load transfer from the concrete to the steel at the connection is critical.
- What is the effect of the bolt pre-tension on the connection capacity? Higher pre-tension means higher friction and a stiffer connection, but it also means higher stresses in the bolts and the flanges.
- What is the failure mode? The paper likely identifies the failure mode from the experimental data. This is important because it tells you what to inspect and what to design against.
5. Study Insights and Implications for Practice
This paper is a reminder that the connection is often the critical element in a structure, and that the connection design must be based on a thorough understanding of the load transfer mechanism. In a pipe curtain, the flange bolt connection is the only thing holding the structure together, and its failure would be catastrophic.
For a pipe fabricator, the manufacture of the flanges and the welding of the flanges to the pipes is a critical quality issue. The flange must be machined to the correct dimensions, the bolt holes must be accurately drilled, and the weld must be sound. The bolts must be supplied with the correct grade and the correct length, and they must be tightened to the specified pre-tension.
6. Reference Value and Outlook
The paper is a valuable reference for anyone involved in the design or construction of pipe curtain structures. It provides experimental data on the behaviour of the connection under eccentric compression, which is the most critical loading condition. The outlook is that pipe curtain structures will continue to be used in underground construction, and that the connection design will become more refined as more experimental data becomes available.
Zhuojin Pipe Fitting Co., Ltd