Vertical Bearing Capacity of Large-Diameter Steel Pipe Piles Considering Soil Plug Effects
1. Literature Overview and Core Findings
The paper presents a calculation method for the vertical bearing capacity of large-diameter open-ended steel pipe piles, with a specific focus on the soil plug effect. When an open-ended pipe pile is driven into the ground, soil enters the pile and forms a plug. The behaviour of this plug determines whether the pile behaves as an open-ended pile or as a closed-ended pile, and this has a significant effect on the bearing capacity.
From my experience in offshore and marine construction, this is a topic of great practical importance. Large-diameter steel pipe piles are used extensively for offshore platforms, jetties, and marine structures. The pile is driven by a hammer, and the driving resistance is monitored to determine the pile capacity. The soil plug effect is one of the key factors that determines the driving resistance and the ultimate capacity.
2. Technical Interpretation: The Soil Plug Effect
2.1 Open-Ended vs. Closed-Ended Behaviour
An open-ended pile can behave in two ways:
- Coring mode: The soil enters the pile and moves up the inside of the pile as the pile is driven. The soil plug moves with the pile, and the pile behaves as an open-ended pile. The bearing capacity is provided by the friction on the outside of the pile and the friction on the inside of the pile.
- Plugging mode: The soil plug becomes wedged inside the pile and moves with the pile as if the pile were closed-ended. The bearing capacity is provided by the friction on the outside of the pile and the end bearing on the soil plug.
The transition from coring mode to plugging mode depends on the pile diameter, the soil properties, and the driving energy. In general, large-diameter piles tend to behave in coring mode, while small-diameter piles tend to behave in plugging mode. The paper likely presents a method to calculate the degree of plugging and the resulting bearing capacity.
2.2 The Plugging Ratio
The plugging ratio is a key parameter that quantifies the degree of plugging. It is defined as the ratio of the height of the soil plug to the height of the soil column that would be present if the pile were fully plugged. A plugging ratio of 1.0 means the pile is fully plugged, and a plugging ratio of 0.0 means the pile is fully coring.
The plugging ratio is not a constant; it changes during driving. As the pile is driven, the soil plug may build up and become more compacted, increasing the plugging ratio. The calculation method in the paper likely accounts for this variation.
3. Engineering Practice: What the Site Needs to Know
3.1 Pile Driving Records
The pile driving record is the most important source of information for verifying the pile capacity. The record includes the hammer energy, the number of blows per unit penetration, and the pile penetration depth. The driving resistance is a measure of the soil resistance, and it can be used to estimate the pile capacity using dynamic pile driving formulas or wave equation analysis.
The soil plug effect is important because it affects the driving resistance. A plugged pile will have a higher driving resistance than an unplugged pile, because the plug provides end bearing. If the plugging effect is not accounted for, the driving resistance will be misinterpreted, and the pile capacity will be underestimated or overestimated.
3.2 Pile Installation and Inspection
The installation of large-diameter pipe piles requires careful planning and execution. The pile must be driven to the correct depth, and the driving must be monitored to ensure that the pile is not damaged. The pile may be driven with an internal hammer, or with an external hammer, and the choice of hammer affects the driving efficiency.
After driving, the pile may be inspected using a variety of methods, including:
- Pile integrity testing: A low-strain impact test is used to detect defects in the pile, such as cracks or necking.
- Static load testing: A static load test is used to verify the pile capacity.
- Dynamic load testing: A dynamic load test, using a PDA (Pile Driving Analyzer), is used to estimate the pile capacity.
4. Key Questions and Reflections
The paper raises several important questions:
- How does the soil plug effect vary with pile diameter? The plugging ratio tends to decrease with increasing pile diameter, but the relationship is not straightforward.
- How does the soil plug effect vary with soil type? The plugging ratio is higher in dense sand than in loose sand, and it is different in clay than in sand.
- How does the soil plug effect vary with driving energy? Higher driving energy tends to promote coring, while lower driving energy tends to promote plugging.
5. Study Insights and Implications for Practice
This paper is a reminder that the behaviour of a pile is not determined by the pile alone, but by the interaction between the pile and the soil. The soil plug effect is a key part of this interaction, and it must be accounted for in the design and installation of large-diameter pipe piles.
For a pipe manufacturer, this paper is relevant because it highlights the importance of the pile geometry. The pile diameter, wall thickness, and the presence of any internal stiffeners or driving shoes all affect the soil plug behaviour. The pipe must be manufactured to the correct dimensions, and the driving shoe must be designed to promote the desired plugging behaviour.
6. Reference Value and Outlook
The paper is a valuable reference for anyone involved in the design or installation of large-diameter pipe piles. It provides a calculation method that accounts for the soil plug effect, and it highlights the practical issues that must be addressed during pile driving. The outlook is that large-diameter pipe piles will continue to be used in offshore and marine construction, and that the understanding of the soil plug effect will continue to improve as more field data becomes available.
Zhuojin Pipe Fitting Co., Ltd