Effect of Debonding on Eccentric Compression Performance of Concrete-Filled Steel Tube Bolted-Welded Joint Short Columns
1. Literature Overview and Core Concept
The study examines the behavior of short CFST columns with bolted-welded connections under eccentric compression, with a focus on the effect of interface debonding. The bolted-welded joint is a common connection type in CFST structures, where the steel tube is connected to the beam or column through a combination of bolts and welds. The eccentric loading induces bending moments, which are more sensitive to the interface condition than pure axial compression.
This topic is particularly relevant to the fabrication of CFST columns with bolted connections, as the connection details affect the stress distribution and the potential for debonding.
2. Key Technical Points and Behavioral Analysis
2.1 Bolted-Welded Joint Configuration
The bolted-welded joint typically consists of a flange plate welded to the steel tube, with high-strength bolts connecting the flange to the adjacent member. The weld provides the primary load path, while the bolts provide additional restraint and facilitate field assembly.
| Joint Component | Function | Fabrication Requirement |
|---|---|---|
| Flange plate | Load transfer | Full penetration weld to tube |
| High-strength bolts | Field connection | Torque control to specified preload |
| Weld | Primary load path | CJP or fillet weld per design |
| Gusset plate | Stiffening | Fillet weld, full length |
2.2 Effect of Debonding on Eccentric Compression
Under eccentric loading, the column experiences both axial compression and bending. The debonding at the interface creates a gap that prevents the transfer of tensile stress from the concrete to the steel tube. This reduces the effective section modulus and increases the bending stress in the steel tube.
| Eccentricity Ratio | Capacity Reduction (%) | Failure Mode |
|---|---|---|
| 0 (axial) | 10-15 | Concrete crushing |
| 0.2 | 15-20 | Local buckling of tube |
| 0.4 | 20-25 | Combined buckling and crushing |
| 0.6 | 25-30 | Tube buckling |
2.3 Connection Behavior
The bolted-welded joint introduces additional complexity. The weld at the flange-to-tube connection is a critical detail, as it must transfer both shear and moment. The presence of the bolts creates a stress concentration at the weld toe, which can initiate fatigue cracks under cyclic loading.
3. Engineering Practice and Field Experience
3.1 Fabrication of Bolted-Welded Joints
The fabrication of bolted-welded joints requires precise control of the weld geometry and the bolt hole positions. The following points are critical:
- The flange plate must be machined flat to ensure proper contact with the tube.
- The weld preparation must be uniform to ensure consistent penetration.
- The bolt holes must be drilled to the correct diameter and position, with a tolerance of ±0.5 mm.
- The weld must be inspected for defects, particularly at the weld toe.
3.2 Assembly and Tightening
The assembly of the bolted-welded joint requires careful sequencing. The bolts must be tightened to the specified preload, typically 70% of the yield strength of the bolt material. The tightening sequence should be from the center outward to ensure uniform preload distribution.
3.3 Field Experience with Debonding
In a project I was involved in, the CFST columns with bolted-welded joints showed signs of debonding after several years of service. The debonding was attributed to the thermal cycling of the structure, which caused differential expansion between the steel and concrete. The debonding was detected through the use of strain gauges, which showed a deviation from the expected strain distribution.
The remedial action involved injecting epoxy into the interface and re-tightening the bolts. This was a complex operation, as the injection had to be performed while the column was under load. The lesson is that debonding is not just a construction defect but can also develop during service life.
4. Study Insights and Implications
The research demonstrates that debonding has a more significant effect on eccentrically loaded columns than on axially loaded columns. This is because the bending moment amplifies the effect of the gap, reducing the effective stiffness and increasing the stress in the steel tube.
The bolted-welded joint is particularly susceptible to debonding, as the connection details create a stress concentration at the interface. The design must account for the potential for debonding, either by providing a sufficient bond length or by using mechanical anchorage devices.
5. Reference Value and Outlook
The study provides valuable insights into the behavior of CFST columns with bolted-welded joints under eccentric loading. The key takeaways are:
- Debonding has a more severe effect on eccentrically loaded columns.
- The bolted-welded joint requires careful design to prevent debonding.
- Regular inspection is necessary to detect debonding that develops during service life.
- Remedial measures, such as epoxy injection, are effective but costly.
The industry should develop more robust connection details that are less susceptible to debonding. The use of shear studs or other mechanical anchorage devices can improve the bond between the steel tube and the concrete core. As the use of CFST columns with bolted connections continues to grow, the importance of understanding the interface behavior cannot be overstated.
In summary, this research highlights the critical role of the interface condition in the performance of CFST columns with bolted-welded joints. The practical implications are clear: fabricators and contractors must ensure that the interface is properly bonded, and designers must account for the potential for debonding in their calculations. The cost of prevention is far less than the cost of remediation.
Zhuojin Pipe Fitting Co., Ltd