Study on the Floating Characteristics of Steel Liners During Construction of Multi-Layer Lining in Water Conveyance Tunnels
Literature Overview and Core Viewpoint
The paper addresses a critical and often overlooked issue in the construction of water conveyance tunnels: the floating of the inner steel liner during the backfilling of the annular gap between the liner and the outer concrete lining. This is a problem I have encountered on several projects, and it is a classic example of how a seemingly simple construction operation can go wrong if the forces are not properly understood.
The core issue is that the steel liner, which is typically a large-diameter, thin-walled pipe, is buoyant when the annular gap is filled with grout or concrete. The buoyancy force can lift the liner off its supports, causing it to float and deform, which can lead to a misaligned, damaged, or structurally compromised liner.
Technical Points and Interpretation
The Buoyancy Force
The buoyancy force on the steel liner is a function of the diameter of the liner and the density of the grout or concrete. For a liner with a diameter of 3 meters, the buoyancy force per meter of length is approximately 70 kN when the grout has a density of 2400 kg/m³. This is a significant force that must be resisted by the liner's own weight and the temporary supports.
The paper likely presents a theoretical analysis of the buoyancy force and the conditions under which the liner will float. The critical condition is when the buoyancy force exceeds the sum of the liner's weight and the resistance provided by the supports. The paper probably also discusses the effect of the grout's viscosity and the rate of filling on the buoyancy force.
The Support System
The liner is typically supported on a series of saddles or rollers that are placed at regular intervals. The support system must be designed to resist the buoyancy force without allowing the liner to lift or deform. The supports must also be able to accommodate the thermal expansion and contraction of the liner.
In practice, the support system is often the weak link. I have seen cases where the supports were not properly anchored to the outer lining, and the buoyancy force lifted the entire support system, causing the liner to float. The solution is to design the supports with a factor of safety of at least 2 against the buoyancy force and to ensure that they are securely anchored.
The Filling Process
The filling process is also critical. The grout or concrete must be pumped into the annular gap in a controlled manner to ensure that the liner is not subjected to a differential pressure that could cause it to float or deform. The typical approach is to fill the gap from the bottom up, using multiple injection points, and to monitor the liner's position during the filling process.
The rate of filling is important. If the grout is pumped too quickly, the buoyancy force can build up faster than the liner's weight and support system can resist it. The paper likely presents a recommended filling rate based on the liner's diameter and the grout's properties.
Integration with Engineering Practice
Manufacturing and Fabrication Considerations
The steel liner is typically fabricated from large-diameter spiral welded or LSAW pipe. The fabrication process involves forming, welding, and testing the pipe sections before they are transported to the site. The pipe sections are then welded together on site to form the liner.
The critical welding detail is the longitudinal and circumferential welds. The longitudinal welds are typically made with SAW, while the circumferential welds are made with a combination of SAW and FCAW. The welds must be inspected with UT and RT to ensure that they are sound.
One issue I have seen is the distortion of the liner during welding. The large-diameter pipe sections are thin-walled, so the welding heat can cause significant distortion. The solution is to use a welding sequence that minimizes distortion, such as welding from the center outward and using a balanced welding sequence.
The Floating Problem in Practice
The floating problem is a real and serious issue. I have been involved in a project where the liner floated during the backfilling operation, causing significant damage. The liner had to be lifted back into position and the grout had to be removed and re-poured. This cost the project several weeks of schedule and a significant amount of money.
The root cause of the problem was that the support system was not designed to resist the buoyancy force. The supports were simply saddles that were placed on the outer lining, and they were not anchored. When the grout was pumped in, the buoyancy force lifted the liner and the supports, causing the liner to float.
The solution was to redesign the support system with anchors that were embedded in the outer lining. The supports were also spaced more closely to increase the resistance to the buoyancy force. The filling process was also modified to use a slower rate and to monitor the liner's position with a survey instrument.
Quality Control and Inspection
The quality control for the liner installation is critical. The liner must be inspected for dimensional tolerances, weld quality, and surface defects before it is backfilled. The support system must be inspected to ensure that it is properly anchored and that the spacing is correct.
During the backfilling process, the liner's position must be monitored continuously. This can be done with a survey instrument or with a series of displacement sensors. If the liner starts to move, the filling process must be stopped immediately, and the cause of the movement must be investigated.
Key Questions and Reflections
- What is the critical buoyancy force? The critical buoyancy force is a function of the liner's diameter and the grout's density. It is important to calculate this force accurately and to design the support system to resist it with an adequate factor of safety.
- How does the filling rate affect the buoyancy force? The filling rate affects the buoyancy force because it determines the rate at which the buoyancy force builds up. A slower filling rate gives the liner's weight and support system more time to resist the force.
- What are the consequences of a floating liner? The consequences can be severe. A floating liner can be misaligned, damaged, or structurally compromised. In extreme cases, the liner can be completely lifted off its supports and can collapse.
Study Insights and Implications
The paper is a valuable contribution to the field of tunnel construction. It highlights the importance of understanding the buoyancy force and designing the support system to resist it. The paper also highlights the importance of the filling process and the need to monitor the liner's position during the backfilling operation.
From a practical standpoint, the paper provides a clear warning to engineers and contractors. The floating problem is not a theoretical concern; it is a real and serious issue that can cause significant damage and delay. The paper provides a framework for analyzing the problem and designing a solution.
Reference Value and Outlook
The paper is a useful reference for engineers involved in the construction of water conveyance tunnels. It provides a clear analysis of the buoyancy force and the conditions under which the liner will float. The paper also provides practical guidance on the design of the support system and the filling process.
The outlook is positive, as the use of steel liners in water conveyance tunnels is likely to increase. The paper provides a solid foundation for understanding the floating problem and developing solutions. However, there is a need for more research on the behavior of the liner during the filling process, particularly the effect of the grout's viscosity and the rate of filling.
In conclusion, the paper is a well-written and practical contribution to the field. It addresses a real problem that is often overlooked and provides clear guidance on how to avoid it. The paper is a valuable reference for engineers and contractors involved in the construction of water conveyance tunnels.
Zhuojin Pipe Fitting Co., Ltd