Steel-Reinforced Steel Pipe Coal Gangue Concrete Composite Columns: Axial Compression Test Insights
Introduction and Research Significance
The axial compression test of steel-reinforced steel pipe coal gangue concrete composite columns addresses a growing interest in using industrial by-products in structural concrete. Coal gangue, a waste material from coal mining, can be used as a coarse aggregate in concrete, but its lower strength and higher porosity compared to natural aggregates raise questions about the performance of composite columns. The steel pipe in this application serves as both a formwork and a confinement element, while the internal steel bone (steel section) provides additional axial load capacity. The literature under review reports on axial compression tests of such composite columns, comparing the behaviour of coal gangue concrete with normal concrete. From a steel pipe perspective, the key question is whether the steel pipe can provide adequate confinement to the lower-strength coal gangue concrete, and whether the composite action is maintained under axial load.
Steel Pipe Role and Material Selection
In a steel-reinforced steel pipe concrete column, the outer steel pipe provides confinement to the concrete core, which enhances the concrete's compressive strength and ductility. The internal steel bone, typically an I-section or H-section, contributes to the axial load capacity and provides a continuous load path through the column. The literature reports that the steel pipe in these tests was Q345 grade with a diameter of 140-200 mm and a wall thickness of 4-6 mm. The key material properties are summarised below:
| Component | Material | Yield Strength (MPa) | Ultimate Strength (MPa) | Role in Composite Action |
|---|---|---|---|---|
| Outer Steel Pipe | Q345B | 345 | 470 | Confinement and axial load |
| Internal Steel Bone | Q235B or Q345B | 235-345 | 370-470 | Axial load and bending resistance |
| Concrete Core | Coal Gangue Concrete | 25-40 (cube) | - | Load transfer and confinement |
| Interface | - | - | - | Bond and composite action |
The literature highlights that the steel pipe-to-concrete bond is critical for composite action. In practice, we achieve this bond through natural adhesion and mechanical interlock, but the bond can be compromised by shrinkage of the coal gangue concrete. Coal gangue concrete has a higher shrinkage than normal concrete, which can create a gap at the pipe-concrete interface, reducing the confinement effect. The paper reports that the use of a steel bone (internal steel section) helps to mitigate this issue by providing an alternative load path, but the confinement effectiveness is still reduced. From a manufacturing perspective, I would emphasise that the steel pipe must be clean and free of oil or rust to ensure adequate bond, and that the internal steel bone must be properly positioned and welded to the pipe at the ends to ensure composite action.
Composite Behaviour and Failure Modes
The axial compression tests reported in the literature reveal several important behavioural aspects. First, the load-strain curve of the composite column exhibits three distinct phases: elastic, elasto-plastic, and plastic. The elastic phase is governed by the stiffness of the steel pipe and the concrete core, while the elasto-plastic phase is characterised by the yielding of the steel pipe and the progressive cracking of the concrete core. The plastic phase is dominated by the confinement effect, where the steel pipe restrains the lateral expansion of the concrete, allowing the column to sustain additional load after the concrete has cracked. The paper reports that the coal gangue concrete columns show a similar overall behaviour to normal concrete columns, but with a slightly lower peak load and a more pronounced softening branch.
The failure modes observed in the tests include local buckling of the steel pipe, crushing of the concrete core, and fracture of the internal steel bone. The literature notes that local buckling of the steel pipe is a critical failure mode, particularly for thin-walled pipes with a diameter-to-thickness ratio greater than 40. In practice, we specify a diameter-to-thickness ratio of no more than 35 to ensure that the steel pipe reaches its yield strength before local buckling occurs. The paper also reports that the internal steel bone can fracture if the column is subjected to high eccentricity, which is a concern for columns in seismic zones. From a practical standpoint, I would recommend that the internal steel bone be designed to yield before the outer pipe, ensuring a ductile failure mode.
Engineering Implications and Insights
The use of coal gangue concrete in composite columns offers significant environmental and economic benefits, but the literature highlights the need for careful design and quality control. The key engineering implications are: first, the confinement effectiveness of the steel pipe is reduced for coal gangue concrete due to higher shrinkage; second, the internal steel bone is essential for maintaining axial load capacity when the concrete core cracks; and third, the diameter-to-thickness ratio of the steel pipe must be controlled to prevent local buckling. In my experience, the most critical quality issue in manufacturing such columns is ensuring the concentricity of the internal steel bone within the outer pipe. If the steel bone is off-centre, the column will exhibit eccentric loading, reducing its axial capacity by up to 20%. The solution is to use a jig or spacer rings to position the steel bone accurately during fabrication, and to verify the position with ultrasonic or radiographic methods before welding the end plates.
For fellow engineers, I would emphasise that the steel pipe in a composite column is not just a formwork; it is a structural element that must be manufactured to tight tolerances and with verified weld quality. The literature provides valuable data on the behaviour of coal gangue concrete composite columns, but the practical success of such columns depends on the quality of fabrication and the attention to detail in the welding and positioning of the internal steel bone. I have seen columns fail prematurely due to poor weld quality at the end plates, which allowed the concrete to leak out during casting, and I have seen columns perform excellently when the fabrication was done with care and the concrete was properly vibrated to fill the annulus completely. The lesson is that composite columns are only as good as the weakest link in the fabrication chain.
Zhuojin Pipe Fitting Co., Ltd