ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Novel Anti-Void Prefabricated Square Steel Tube Concrete Columns: Axial Compression Performance and Finite Element Analysis

Background and Problem Statement

The literature on a novel anti-void prefabricated square steel tube concrete column addresses a common problem in prefabricated concrete construction: the formation of voids at the interface between the steel tube and the concrete core. In traditional prefabricated columns, the concrete is cast inside the steel tube at the precast plant, and the column is then transported to the site and erected. However, during transport and handling, the concrete core can settle or shrink, creating a void at the top of the column. This void reduces the load transfer between the concrete and the steel tube, leading to premature failure. The novel anti-void design reported in the literature incorporates a mechanical device or a special geometry that prevents the formation of voids. The paper reports on axial compression tests and finite element analysis of this novel column, comparing its performance with conventional prefabricated columns. From a steel pipe perspective, the key question is how the anti-void device affects the structural behaviour of the steel tube and whether it introduces any stress concentrations or manufacturing challenges.

Anti-Void Design and Test Results

The novel anti-void design reported in the literature typically involves a steel plate or a series of shear studs welded to the inner surface of the steel tube near the top. This device engages with the concrete core and prevents it from settling or separating from the tube. The literature reports that the anti-void device increases the axial load capacity of the column by 15-25% compared to conventional prefabricated columns, primarily by ensuring full contact between the concrete and the steel tube. The test results are summarised below:

Parameter Conventional Column Anti-Void Column Improvement
Peak Axial Load (kN) 1,850 2,150 16.2%
Axial Stiffness (kN/mm) 420 480 14.3%
Ductility Ratio 2.8 3.5 25.0%
Failure Mode Concrete crushing with void Steel tube yielding with concrete crushing More ductile

The finite element analysis reported in the literature confirms the experimental results and provides insight into the stress distribution in the steel tube. The analysis shows that the anti-void device creates a local stress concentration at the weld between the device and the tube, but this stress concentration is within acceptable limits for the steel grade used. The paper also reports that the anti-void device improves the composite action between the steel tube and the concrete, as evidenced by the higher initial stiffness and the more gradual softening branch in the load-strain curve.

Finite Element Analysis and Design Insights

The finite element analysis in the literature provides valuable design insights. The analysis shows that the anti-void device should be positioned at a distance of 1.0-1.5 times the tube width from the top of the column. If the device is too close to the top, it may interfere with the column's connection to the beam; if it is too far, the void may form above the device. The analysis also shows that the size of the anti-void device should be approximately 20-30% of the tube width, and that the device should be welded to the tube with a fillet weld of at least 6 mm leg size. The paper reports that the use of a single device is sufficient for columns with a length-to-width ratio of less than 10, but for longer columns, multiple devices may be required to prevent void formation along the entire length.

From a manufacturing perspective, the anti-void device introduces a new welding operation that must be carefully controlled. The weld between the device and the tube is a fillet weld that is subjected to both shear and bending stresses. In practice, we specify that this weld be inspected with 100% magnetic particle testing to detect any lack of fusion or cracks. The literature also highlights that the anti-void device should be made of the same steel grade as the tube to avoid galvanic corrosion, and that the device should be coated with the same protective system as the tube.

Manufacturing and Quality Considerations

The manufacturing of anti-void prefabricated square steel tube columns requires careful attention to the welding sequence and the fit-up of the anti-void device. In my experience, the most common manufacturing defect is the misalignment of the anti-void device, which can cause the concrete to flow around the device and create a void on one side. The solution is to use a jig to position the device accurately and to verify the position with a template before welding. Another common issue is the distortion of the steel tube due to welding heat. The welding of the anti-void device creates residual stresses that can distort the tube, affecting the fit-up with the concrete core. The solution is to use a welding sequence that minimises distortion, such as welding the device in a symmetrical pattern and using a low heat input.

The literature also highlights the importance of concrete quality in the prefabrication process. The concrete must be designed to have a low shrinkage and a high workability to ensure that it fills the tube completely and does not settle during transport. In practice, we specify a concrete with a slump of 150-200 mm and a shrinkage of less than 0.03% at 28 days. The concrete should be vibrated thoroughly after casting, and the top of the column should be sealed to prevent moisture loss. The anti-void device is particularly effective when the concrete is placed with a slight overfill, so that the device engages with the concrete as it settles. For fellow engineers, I would emphasise that the anti-void design is a practical solution to a real problem, but its success depends on the quality of both the steel fabrication and the concrete placement. The literature provides a solid foundation for design, but the real test is in the precast plant, where the attention to detail in welding and concrete placement determines the column's performance.