ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

25Mn Cold-Drawn Steel Pipe Straightening Fracture: Failure Analysis and Root Cause Investigation

Overview and Core Findings

This study presents a comprehensive failure analysis of a 25Mn cold-drawn steel pipe that fractured during the straightening process. The fracture is a classic example of a manufacturing defect that can have severe consequences if not properly diagnosed and corrected. From my perspective as a veteran of the steel pipe industry, this type of failure is all too familiar, and the study's findings align closely with what I have observed on the plant floor. The cold-drawn process introduces significant residual stresses and work hardening into the pipe, and the straightening operation, which is intended to correct the pipe's geometry, can inadvertently cause fracture if the process parameters are not properly controlled. The study's root cause analysis is thorough and provides a clear roadmap for preventing similar failures in the future.

Technical Interpretation and Process Analysis

The fracture analysis reveals that the pipe failed in a brittle manner, with a clean fracture surface and minimal plastic deformation. This is characteristic of a failure caused by high residual stresses combined with a material that has become embrittled due to cold work. The 25Mn steel grade is a low-alloy carbon steel that is commonly used for cold-drawn pipes due to its good combination of strength and ductility. However, the cold-drawing process can reduce the material's ductility significantly, especially if the reduction ratio is high or if the drawing speed is excessive. The straightening process, which typically uses a multi-roll straightener, applies cyclic bending stresses to the pipe. If the residual stresses from the drawing process are not relieved, these cyclic stresses can combine to exceed the material's fracture strength. The table below summarises the key parameters and findings from the study.

Parameter Value / Finding Significance
Material grade 25Mn (0.22-0.29% C) Medium carbon steel, susceptible to work hardening
Cold-drawing reduction 15-25% typical Higher reduction increases residual stress
Straightening rolls 6-8 rolls, alternating Cyclic bending induces fatigue-like loading
Fracture surface Brittle, cleavage facets Indicates high stress concentration
Hardness at fracture 220-240 HB Higher than base material (180-200 HB)
Residual stress 60-70% of yield strength Exceeds safe threshold for straightening
Straightening speed 20-40 m/min Higher speed increases strain rate
Failure location Mid-span of straightener Maximum bending moment region

The study's metallographic analysis reveals that the fracture initiated at a surface defect, likely a small scratch or dent from the drawing die, which acted as a stress raiser. The combination of this stress concentration, the high residual stress, and the reduced ductility of the cold-worked material led to the brittle fracture. The study also identifies the straightening process parameters as a contributing factor, specifically the roll spacing and the amount of bending applied. If the straightener is set to apply excessive bending, the pipe will experience stresses that approach or exceed its yield strength, leading to fracture. The study's recommendation to reduce the straightening speed and to use a larger roll spacing is consistent with what I have seen in practice, where slower speeds and gentler bends allow the material to relax and reduce the peak stress.

Engineering Practice and Lessons Learned

This failure analysis highlights several important lessons for the steel pipe manufacturing industry. First, the quality of the incoming material must be carefully controlled. The 25Mn steel should be supplied with a fully killed, fine-grained microstructure to ensure adequate toughness. Second, the cold-drawing process must be designed to minimise residual stress. This can be achieved by using a lower reduction ratio, applying a stress-relief anneal after drawing, or using a drawing die with a proper approach angle and bearing length. Third, the straightening process must be carefully set up and monitored. The roll spacing and the amount of bending should be adjusted based on the pipe's diameter and wall thickness, and the straightening speed should be kept within the recommended range. I have seen cases where the straightener was set to a fixed configuration for all pipe sizes, resulting in excessive bending for smaller pipes and insufficient straightening for larger ones. The study's findings also underscore the importance of non-destructive testing, particularly surface inspection, to detect defects that could serve as fracture initiation sites. Magnetic particle inspection or eddy current testing should be performed on all cold-drawn pipes before straightening, and any surface defects should be removed or the pipe should be rejected.

Study Insights and Implications

The study provides a valuable reference for failure analysis in the steel pipe industry, demonstrating the importance of a systematic approach to root cause investigation. The key insight is that the fracture was not caused by a single factor, but by the combination of high residual stress, reduced ductility, and a surface defect. This highlights the need for a holistic approach to process control, where the material, the drawing process, and the straightening process are all considered as an integrated system. For the industry, this study reinforces the importance of stress relief treatments, whether through annealing or other methods, to reduce the residual stress in cold-drawn pipes. It also emphasises the need for rigorous quality control, including dimensional inspection, surface inspection, and mechanical testing, at every stage of the manufacturing process. The study's findings should be incorporated into standard operating procedures for cold-drawn pipe manufacturing, and the recommended process parameters should be validated through production trials. The failure analysis methodology described in the study, including the metallographic examination, hardness testing, and stress analysis, should be adopted as a standard approach for investigating similar failures in the future.