ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Bearing Capacity Evaluation and Rational Selection of Steel Tube Concrete Arch Frames for Highway Tunnels

1. What the Study Really Addresses

This research tackles a problem I have seen misjudged on more tunnel sites than I care to count: how to evaluate the load-bearing capacity of steel tube concrete (CFST) arch frames and, more importantly, how to select the right tube so the frame does not become the weak link in the support system. The study proposes evaluation indices that go beyond simple axial compression checks, and it rightly draws attention to the composite action between the steel tube and the concrete core. For a man who has shipped thousands of tonnes of seamless and welded pipe, the message is clear: the tube is not just a formwork, it is a structural member whose geometry, wall thickness and weld quality decide whether the arch carries the load or fails quietly behind the shotcrete.

2. Steel Pipe Selection and Composite Action

The choice of steel tube for a tunnel arch frame is a commercial and technical compromise. The table below reflects what I have specified on real projects, and what the research confirms as sensible practice.

Parameter Seamless Tube ERW/HFW Tube LSAW Tube
Typical diameter (mm) 89–219 89–219 219–508
Wall thickness (mm) 5–12 4–10 8–16
Grade Q235B, Q345B Q235B, Q345B, Q420 Q345B, Q420, Q460
Weld seam quality No seam HFW seam, NDT per GB/T 13793 SAW seam, 100% UT per GB/T 9711
Concrete filling Easy, uniform Easy, uniform Requires care at weld seam
Local buckling resistance Excellent Good Good, but thicker wall needed
Cost per tonne High Moderate Moderate to high
Typical application Small span, high ground class Medium span, standard arches Large span, heavy overburden

The composite action is what makes CFST arches outperform plain steel ribs. The concrete core restrains inward local buckling of the tube wall, and the tube confines the concrete, raising its compressive strength. The study's evaluation indices should include the confinement factor, the diameter-to-thickness ratio (D/t), and the concrete strength grade. In my experience, a D/t ratio above 40 for Q345 tube invites local buckling before the concrete reaches its full confined strength, so I always push for D/t in the 25–35 range for tunnel arches. The concrete grade matters too: C30 is the bare minimum, but C40 with a shrinkage-compensating admixture gives far better contact and avoids the voids I have found when cores were pulled from arches in wet ground.

3. Practical Evaluation and Selection on Site

On site, the evaluation index is only as good as the data behind it. The study rightly calls for a combined check of axial capacity, bending capacity and the interaction between them, but the real challenge is the ground condition. I have seen arches selected purely on axial load and then fail in bending when the tunnel face yielded unevenly. My rule of thumb: always check the arch for the worst-case combination of axial load and bending moment that the excavation sequence can produce, not just the design load. The selection of tube size should also consider the connection to the foot plate and the lattice girder ties. A 180 mm diameter seamless tube with a 10 mm wall is a workhorse, but if the end plate weld is a single-pass fillet, it will crack under cyclic loading from blasting and excavation. I insist on full-penetration welds at the arch ends, and I have seen too many shop drawings that specify a 6 mm fillet where an 8 mm full-penetration butt weld was needed.

4. Lessons from the Plant and the Tunnel Face

The study is a good reminder that the steel tube is not a commodity. I have rejected entire lots of ERW tube for tunnel arches because the HFW seam showed cold weld or lack of fusion on UT, and I have watched a tunnel arch buckle at the seam because the mill had used a lower grade than ordered. The concrete side is equally unforgiving: if the concrete is not vibrated properly, voids form at the top of the arch, and the tube then carries the full load alone, which it was never designed to do. The study's contribution is to make the evaluation index a function of both the tube and the concrete, which is exactly how the structure behaves. My final word on selection: do not buy the cheapest tube per tonne, buy the tube that gives you the lowest total cost per metre of tunnel, including the cost of remedial grouting, rework and the risk of a collapse. That is the number that matters, and this study helps you get closer to it.