ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Experimental Comparison of Aircraft Fuel Tank Inerting Processes Using NEA and MIG

Literature Overview and Core Findings

This paper from Nanjing University of Aeronautics and Astronautics compares two approaches to fuel tank inerting: Nitrogen-Enriched Air (NEA) from an On-Board Inert Gas Generation System (OBIGGS) and Mixed Inert Gas (MIG) from a Green On-Board Inert Gas Generation System (GOBIGGS). The MIG gas is primarily CO2, N2, and O2, while NEA is mostly N2 with a reduced O2 content. The key physical difference is that CO2 has roughly 20 times the solubility of N2 in jet fuel, which means the two gases behave very differently when dissolved in the fuel. The authors built a test bench and ran two modes: ullage washing, where the inert gas is injected into the space above the fuel, and fuel scrubbing, where the gas is bubbled through the fuel itself.

The results are clear and, from a safety engineering standpoint, important. In ullage washing, the oxygen concentration in both the ullage and the fuel drops at nearly the same rate regardless of whether you use NEA or MIG. In fuel scrubbing, however, MIG leaves higher oxygen concentrations in both the ullage and the dissolved oxygen in the fuel compared to NEA. That is a counterintuitive result if you assume that higher CO2 solubility means better inerting. The reason is that CO2 dissolves so readily into the fuel that it is pulled out of the gas phase, leaving the remaining gas with a higher oxygen fraction. The scrubbing action actually enriches the ullage oxygen concentration when using MIG.

Technical Parameters and Process Comparison

Parameter NEA (OBIGGS) MIG (GOBIGGS) Practical Significance
Primary inerting gas N2 with reduced O2 CO2, N2, O2 mixture CO2 has ~20x higher solubility in jet fuel
Ullage washing performance Rapid O2 reduction Nearly identical to NEA Both methods acceptable for ullage washing
Fuel scrubbing performance Lower ullage and dissolved O2 Higher ullage and dissolved O2 MIG scrubbing is less effective than NEA
System complexity Higher (membrane or PSA) Lower (flameless catalytic combustion) GOBIGGS simpler and lighter
Safety consideration Non-flammable, stable CO2 can dissolve into fuel, altering properties Must monitor fuel acidity and contamination

The table above is what I would use in a design review. The critical takeaway is that the choice of inerting gas is not just about oxygen displacement; it is about the interaction between the gas and the fuel. CO2 is a great inerting gas in terms of fire suppression, but its high solubility means it does not stay in the ullage where you need it. For fuel scrubbing, NEA wins because N2 is less soluble and remains in the gas phase longer, maintaining a lower oxygen concentration in the ullage.

Engineering Practice and Safety Implications

I have spent decades in industries where tank inerting is a daily concern, from offshore oil storage to chemical processing, and this paper highlights a subtlety that is easy to miss. When you inject an inert gas into a tank, you are not just displacing oxygen; you are also changing the vapor composition above the liquid. If the inert gas dissolves into the liquid, it can actually pull flammable vapors out of the liquid into the ullage, increasing the fire risk. This is exactly what happens with CO2 in jet fuel. The paper shows that MIG scrubbing actually increases the oxygen concentration in the ullage, which is the opposite of what you want.

In my experience, the most dangerous situation is when a tank is partially filled and you are trying to inert the ullage. If you use a gas that dissolves into the liquid, you will never achieve a stable inert atmosphere because the gas keeps being absorbed and the oxygen concentration creeps back up. This paper quantifies that effect and gives me a clear rule: for fuel scrubbing, use NEA; for ullage washing, either works, but NEA is safer because it does not introduce CO2 into the fuel.

Key Questions and Reflections

The paper does not address the long-term effects of CO2 dissolution on fuel quality. Jet fuel has strict specifications for acidity, particulate contamination, and thermal stability. If CO2 dissolves into the fuel and reacts with water or additives, it could form carbonic acid, which would degrade the fuel. I would want to see a study on fuel property changes after prolonged MIG scrubbing before I would approve that system for a commercial aircraft.

Another question is the effect of temperature and pressure on the solubility difference. The tests were presumably run at ambient conditions, but aircraft fuel tanks operate at varying temperatures and pressures, especially during climb and descent. At high altitude, the lower pressure would reduce CO2 solubility, potentially changing the relative performance of MIG and NEA. This is a critical gap for a safety-critical application.

Study Insights and Implications

This paper is a valuable contribution to the field of aircraft fuel tank inerting because it challenges the assumption that a higher solubility inert gas is always better. In fact, the opposite is true for fuel scrubbing. The practical implication is that system designers should not just look at the oxygen displacement capacity of an inert gas; they must also consider its solubility in the fuel and the resulting effect on ullage oxygen concentration.

For my own work in pipeline and tank inerting, this paper reinforces a lesson I have learned the hard way: always test the inerting gas against the actual liquid in the tank, not just against air. A gas that works perfectly for a water-filled tank may be useless for a hydrocarbon-filled tank. The difference is in the solubility and the vapor-liquid equilibrium.

Reference Value and Outlook

This paper is a solid reference for anyone designing fuel tank inerting systems, whether for aircraft, ships, or ground storage. It provides a clear experimental comparison and highlights a subtle but critical difference between two commonly considered inerting gases. I would keep it in the safety engineering library and pull it out whenever we are evaluating a new inerting system.

The next step in this research should be to test the MIG system under simulated flight conditions, including temperature and pressure variations, and to measure the effect of CO2 dissolution on fuel properties over time. Until that is done, I would be cautious about approving MIG for fuel scrubbing in a commercial aircraft.