ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Metallurgical Insights into Aluminium/Galvanized Steel Pulse MIG Brazed Joints

What the Paper Really Tells Us

This study by Qin Guoliang and colleagues at Shandong University addresses one of the most persistent headaches in dissimilar metal joining: getting aluminium to stick to steel without creating a brittle intermetallic layer that fails in service. The authors used a digital pulse MIG machine with ER4043 filler wire to join 6013-T4 aluminium alloy sheet to galvanized steel, and they systematically varied heat input to see how it affected joint microstructure and mechanical performance. The key finding is that the Fe-Al intermetallic compound (IMC) layer thickness at the brazed interface ranges from 1.05 to 4.50 μm, and it grows with increasing heat input. The tensile strength peaks at 229 MPa with a heat input of 850 J/cm, and the fracture location shifts from the brazed interface (brittle) to the aluminium heat-affected zone (ductile) as heat input increases.

The Metallurgy Behind the Numbers

The IMC layer is the critical factor in any aluminium-to-steel joint. The authors identified three distinct intermetallic phases — FeAl₂, Fe₂Al₅ and Fe₄Al₁₃ — growing in a jagged or tongue-like morphology into the weld. This is exactly what I have seen in failed dissimilar joints pulled apart on site. The Fe₂Al₅ phase is particularly problematic because it forms rapidly and grows in a needle-like fashion, acting as a stress concentrator. The study also found a zinc-rich zone at the weld toe composed of Zn-Al eutectic, aluminium-rich α solid solution and Fe₃Al. This zinc-rich zone is a direct consequence of the galvanized coating on the steel, and while it helps wetting, it also creates a low-melting-point region that can be a site for hot cracking if the process is not carefully controlled.

Practical Implications for Shop Floor and Site

The heat input window identified in this paper — around 850 J/cm for optimal strength — is narrow and demands precise control. In my experience, this is where many shops go wrong. Operators on a production line often push heat input up to get better fusion, not realising that they are thickening the IMC layer and embrittling the joint. The practical rules I would give any engineer:

  1. The IMC layer must be kept below approximately 5 μm for any structural application, and ideally below 3 μm for dynamic or fatigue-loaded joints.
  2. Heat input must be monitored continuously, not just set at the start. A digital pulse MIG machine with closed-loop control is essential for this application.
  3. The galvanized coating thickness on the steel side matters more than most people think. Heavy coatings produce excessive zinc vapour, which causes porosity and disrupts the arc.

Lessons and Reflections

I have seen this exact failure mode on a shipyard project where aluminium superstructure was welded to steel deck using a similar approach. The welds looked perfect on the surface, but after a few months of sea service, cracks appeared along the brazed interface. The root cause was an IMC layer that had grown to nearly 8 μm because the welder had increased current to compensate for poor fit-up. The fix was not better welding technique — it was better fit-up and stricter heat input control. This paper gives me the metallurgical justification for the limits I have been enforcing for years. The 229 MPa tensile strength at 850 J/cm is a realistic figure for production, but only if the process is controlled within a tight window. I would also note that the study used ER4043 filler, which is a common choice, but in my experience ER4047 (with higher silicon content) can give slightly better wetting on galvanized steel, though it is more prone to hot cracking in the aluminium itself.

Conclusion

This paper is a solid contribution to the practical understanding of aluminium-to-steel brazed joints. It confirms what many of us have learned the hard way: the IMC layer is the master variable, and heat input is the master control. For anyone running this process in production, the message is clear — monitor heat input, control fit-up, and verify IMC thickness on first-off samples before releasing the joint for service. The 850 J/cm sweet spot is a good starting point, but it must be validated against your specific material combination, coating thickness and joint design.