ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Microstructure and Composition of Multi-Pass MIG Welded 7N01 Aluminum Alloy Joints

Literature Overview and Core Contribution

This paper by She Yadong and colleagues from Hebei University of Science and Technology examines the microstructure and composition of multi-pass MIG welded 7N01 aluminum alloy joints. The study focuses on 12 mm thick 7N01 aluminum alloy plate welded with pulsed MIG in a butt joint configuration. The authors used optical microscopy and electron probe microanalysis (EPMA) to characterize the weld joint microstructure and elemental distribution.

The key contribution is the identification of a fine equiaxed grain layer near the fusion line, which forms due to the re-solidification of partially melted and unmixed base metal. The authors also identified elemental segregation of Mg and Zn at grain boundaries and characterized the grain size differences between the root pass, fill passes, and cap passes.

Technical Interpretation and Microstructural Analysis

The paper reports several important microstructural findings:

Feature Observation Practical Consequence
Fusion line region Fine equiaxed grain layer This is the unmixed zone (UMZ) where base metal is partially melted and re-solidified without mixing with filler metal
Grain boundary segregation Mg and Zn enrichment These elements form low-melting-point eutectics that can cause hot cracking
Root pass grain size Larger than fill and cap passes Due to insufficient liquid metal flow and fewer heterogeneous nucleation sites
Weld bead interfaces Grain refinement and epitaxial growth Prior weld bead is partially remelted; subsequent bead grows epitaxially on the remelted grains

The fine equiaxed grain layer near the fusion line is a critical finding. This layer forms when the base metal is heated to a temperature between the solidus and liquidus, causing partial melting. The partially melted base metal then re-solidifies without mixing with the filler metal, forming a zone with a different composition from both the base metal and the weld metal. This unmixed zone (UMZ) is often a site of weakness because it has different mechanical properties from the surrounding material.

The Mg and Zn segregation at grain boundaries is particularly concerning. In 7N01 aluminum alloy, Mg and Zn are the primary alloying elements that provide strength through precipitation hardening. However, when these elements segregate to grain boundaries, they can form low-melting-point eutectics (Mg₂Si, MgZn₂) that reduce the solidus temperature and increase the susceptibility to hot cracking. The paper identifies this segregation in the equiaxed grain layer, which is a potential site for hot cracking during welding.

Integration with Engineering Practice

From my experience with aluminum welding, the 7N01 alloy is used extensively in rail car structures, particularly in Japan and China. It is a high-strength aluminum alloy with good weldability, but it requires careful control of the welding process to avoid hot cracking and to maintain joint strength. The paper's findings have direct implications for welding procedure development.

First, the identification of the equiaxed grain layer near the fusion line highlights the importance of controlling the heat input. If the heat input is too high, the base metal will be heated above the solidus temperature, creating a wide partially melted zone. If the heat input is too low, the base metal will not melt sufficiently, creating a lack of fusion. The optimal heat input should produce a narrow partially melted zone with a thin equiaxed grain layer.

Second, the Mg and Zn segregation at grain boundaries is a concern for hot cracking. In my experience, hot cracking in 7N01 aluminum alloy is most likely to occur in the equiaxed grain layer near the fusion line, where the low-melting-point eutectics are concentrated. To prevent hot cracking, we need to control the welding parameters to minimize the width of the partially melted zone and ensure that the grain boundary eutectics are not continuous.

Third, the grain size difference between the root pass and the fill/cap passes is a practical concern. The root pass has larger grains because the liquid metal flow is insufficient, resulting in fewer heterogeneous nucleation sites. This means the root pass has lower strength and toughness than the fill and cap passes. In multi-pass welding, the root pass is often the critical section for structural integrity, so this grain size difference is a concern.

Key Questions and Reflections

The paper raises several important questions for practical application:

  1. Hot cracking susceptibility: The paper identifies Mg and Zn segregation at grain boundaries but does not directly assess hot cracking susceptibility. In production, we would need to perform hot cracking tests (e.g., Varestraint test) to determine the susceptibility of the weld joint to hot cracking under different welding parameters.
  2. Mechanical properties: The paper focuses on microstructure and composition but does not report mechanical properties. In production, we need to know the tensile strength, yield strength, elongation, and impact toughness of the weld joint to determine whether it meets the design requirements. The grain size differences between passes would affect the mechanical properties, with the root pass likely having lower strength.
  3. Post-weld heat treatment: The paper does not discuss post-weld heat treatment. In production, we may need to perform post-weld heat treatment to relieve residual stresses and improve the mechanical properties. The Mg and Zn segregation at grain boundaries could be affected by post-weld heat treatment, and this needs to be investigated.
  4. Filler metal selection: The paper does not specify the filler metal used. In production, the filler metal selection is critical for achieving the desired joint properties. For 7N01 aluminum alloy, the typical filler metals are ER5356 (Al-Mg) or ER4043 (Al-Si). The filler metal composition affects the weld metal microstructure and the susceptibility to hot cracking.

Study Insights and Implications

The most valuable insight from this paper is the identification of the equiaxed grain layer near the fusion line and the Mg/Zn segregation at grain boundaries. These findings provide a microstructural basis for understanding the hot cracking susceptibility of 7N01 aluminum alloy welds. For fellow engineers, I would emphasize the following practical considerations:

  1. Heat input control: The width of the equiaxed grain layer is directly related to the heat input. To minimize the equiaxed grain layer, we should use the lowest heat input that achieves complete fusion. This is a balance between avoiding lack of fusion and minimizing the partially melted zone.
  2. Interpass temperature control: The grain size of the fill and cap passes is affected by the interpass temperature. If the interpass temperature is too high, the prior weld bead will be partially remelted, creating a large equiaxed grain layer at the bead interface. We should control the interpass temperature to minimize this effect.
  3. Root pass quality: The root pass has larger grains due to insufficient liquid metal flow. To improve the root pass quality, we should use a higher welding current or a different welding technique (e.g., backing gas or backing plate) to improve the liquid metal flow and promote heterogeneous nucleation.
  4. Hot cracking prevention: The Mg and Zn segregation at grain boundaries increases the hot cracking susceptibility. To prevent hot cracking, we should use a filler metal with a lower Mg and Zn content, or we should use a welding technique that minimizes the width of the partially melted zone.

The paper's findings are also relevant to the standards governing aluminum welding. ASME Section IX and ISO 15614 require that welding procedures be qualified by testing, including mechanical testing and visual inspection. The microstructural findings in this paper provide a basis for understanding why certain welding procedures produce acceptable joints while others do not. For example, if a welding procedure produces a wide equiaxed grain layer with continuous grain boundary eutectics, the joint may fail the hot cracking test. By understanding the microstructural basis for hot cracking, we can develop welding procedures that produce acceptable joints.

Concluding Remarks

This paper provides a detailed microstructural and compositional analysis of multi-pass MIG welded 7N01 aluminum alloy joints. The key findings are the formation of a fine equiaxed grain layer near the fusion line, the segregation of Mg and Zn at grain boundaries, and the grain size differences between the root, fill, and cap passes. These findings have direct implications for welding procedure development, particularly in controlling heat input, interpass temperature, and filler metal selection. The equiaxed grain layer is a potential site for hot cracking due to the Mg and Zn segregation, and the root pass has larger grains that may result in lower mechanical properties. For engineers working with 7N01 aluminum alloy, this paper provides valuable microstructural insights that can guide the development of welding procedures that produce high-quality joints. I would recommend that welding engineers study this paper carefully and consider the microstructural implications when developing welding procedure specifications for 7N01 aluminum alloy.