ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Bypass Current MIG Arc Brazing Characteristics for Aluminum/Titanium Dissimilar Metal Joints

Literature Overview

This paper by Miao Yugang et al., published in Transactions of the China Welding Institution (2015, Vol. 36, No. 1), investigates the bypass current MIG arc brazing process for joining 1 mm thick 6061 aluminum alloy to TC4 titanium alloy. The study uses a novel approach where a portion of the welding current is diverted through a bypass circuit, allowing the aluminum to melt and wet the titanium surface without melting the titanium itself. This creates a brazed joint rather than a fusion weld, which is critical because titanium and aluminum form brittle intermetallic compounds (IMCs) when melted together. The authors report uniform, aesthetically pleasing weld bead formation and characterize the joint using metallography, scanning electron microscopy (SEM), and tensile testing.

Core Findings and Technical Interpretation

The bypass current MIG arc brazing technique is a clever solution to the fundamental challenge of joining aluminum to titanium. When these two metals are fusion welded, they form brittle intermetallic compounds such as TiAl3, TiAl, and Ti3Al, which severely degrade joint properties. By controlling the heat input so that only the aluminum melts, the process creates a brazed joint with a thin IMC layer that is less detrimental.

Parameter Value Practical Significance
Joint shear strength 182.6 MPa 97.6% of aluminum base metal strength
Fracture location Aluminum HAZ Desirable failure mode — not at the interface
IMC types near Ti side AlTi Indicates Ti-rich intermetallic formation
IMC types near Al side Al3Ti, TiSi2 Al-rich intermetallics with silicon
Transition phase Al11Ti5 Forms due to non-uniform temperature distribution
Fracture characteristics Necking observed Ductile failure in aluminum HAZ

The joint shear strength of 182.6 MPa, which is 97.6% of the aluminum base metal strength, is an excellent result. The fact that fracture occurs in the aluminum HAZ with visible necking indicates that the joint interface is not the weakest link—the aluminum base metal governs the joint strength. This is exactly what we want to achieve in dissimilar metal joining: the joint should be stronger than the weaker base metal.

The IMC layer analysis is particularly interesting. The formation of AlTi near the titanium side and Al3Ti near the aluminum side suggests a gradient in IMC composition across the interface. The presence of TiSi2 indicates that silicon from the filler wire (likely ER4043 or a similar silicon-containing filler) is participating in the IMC formation. The transition phase Al11Ti5 is notable because it forms due to non-uniform temperature distribution in the weld pool, which is a common challenge in brazing processes.

Engineering Practice and Standards Considerations

For dissimilar metal joining, the quality requirements are typically more stringent than for similar metal welding. The following considerations are critical:

  1. IMC layer thickness control. The IMC layer thickness is the primary factor determining joint strength and ductility. In general, an IMC layer thickness of less than 10 μm is considered acceptable for aluminum-titanium joints. The bypass current MIG arc brazing process provides better control over IMC thickness than conventional fusion welding because the heat input can be precisely controlled.
  2. Joint design and fit-up. For brazed joints, the joint design must ensure proper capillary action and wetting. The 1 mm thick aluminum and titanium sheets used in this study are representative of thin-section applications, but thicker sections may require different joint designs. I would recommend consulting the applicable standards (e.g., AWS C3.7 for brazing) for joint design guidance.
  3. Corrosion resistance. Dissimilar metal joints are susceptible to galvanic corrosion due to the potential difference between aluminum and titanium. In marine or other corrosive environments, this can be a significant issue. I would recommend specifying appropriate corrosion protection measures, such as sealing the joint with a suitable coating or using a corrosion inhibitor.
  4. NDT requirements. The paper does not discuss NDT, but for critical applications, ultrasonic testing or radiography should be considered to detect lack of wetting, porosity, or other brazing defects. However, the thin sections used in this study may present challenges for conventional NDT methods.

Key Questions and Reflections

One question that arises from this research is the long-term stability of the joint under service conditions. The IMC layer, while thin, may grow over time due to diffusion, especially at elevated temperatures. This is a known issue in aluminum-titanium joints and can lead to embrittlement and reduced joint strength. I would recommend conducting aging tests at service temperatures to evaluate the long-term stability of the joint.

Another consideration is the scalability of the bypass current MIG arc brazing process. The paper uses 1 mm thick material, which is relatively thin. For thicker sections, the heat input required to melt the aluminum without melting the titanium becomes more challenging, as the titanium's heat sink effect is greater. I would recommend conducting trials on thicker sections to evaluate the process's scalability.

Study Insights and Practical Recommendations

Based on my experience and this research, I offer the following recommendations for aluminum-titanium dissimilar metal joining:

Conclusion

This research presents a promising method for joining aluminum to titanium using bypass current MIG arc brazing, achieving excellent joint strength (97.6% of aluminum base metal) with fracture occurring in the aluminum HAZ. The IMC layer analysis provides valuable insights into the phase formation and its relationship to process parameters. However, the long-term stability of the joint under service conditions, particularly at elevated temperatures, requires further investigation. As an industry veteran, I would emphasize that dissimilar metal joining demands rigorous process control and comprehensive joint evaluation. The bypass current MIG arc brazing technique is a valuable addition to the joining engineer's toolkit, but its successful implementation requires careful attention to process parameters, joint design, and service conditions.