ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Dissimilar Metal Welding of Stainless Steel to Aluminium: Interfacial Compounds and the Limits of Laser-MIG Hybrid Brazing

Literature Overview and Practical Relevance

This study by Zhu Zongtao and colleagues from Southwest Jiaotong University addresses one of the most challenging problems in welding engineering: joining stainless steel to aluminium. The authors used laser-MIG hybrid welding and conventional MIG welding to produce butt joints between 2 mm thick 304 stainless steel and 6061 aluminium alloy, then compared the interfacial intermetallic compounds, microstructure and mechanical properties of the two processes.

The results are both informative and counterintuitive. The laser-MIG hybrid joint had a thicker intermetallic compound layer, approximately 5 μm, compared to about 3 μm for the single MIG joint. Yet the hybrid joint achieved a tensile strength of 105 MPa, which was 10.8 MPa higher than the MIG joint. This is a fascinating result because it challenges the conventional wisdom that thinner intermetallic layers always produce stronger joints.

For those of us in the pipe and fitting industry, dissimilar metal welding between stainless steel and aluminium is not a common application, but the principles are directly relevant to any dissimilar metal joint where intermetallic compounds form. The same considerations apply to stainless steel to copper, titanium to steel, or any combination where the two materials have limited mutual solubility.

Technical Interpretation: The Intermetallic Compound Dilemma

The fundamental problem in welding stainless steel to aluminium is that iron and aluminium form a series of brittle intermetallic compounds, including FeAl, FeAl2, Fe2Al5, Fe3Al, and Fe4Al13. These compounds are hard and brittle, and they provide a path for crack propagation. The thickness of the intermetallic layer is critical: if it is too thick, the joint becomes brittle and fails at low stress. If it is too thin, there may be insufficient bonding between the two materials.

The authors found that the laser-MIG hybrid joint contained both FeAl2 and Fe4Al13, with a total thickness of about 5 μm. The single MIG joint contained primarily Fe4Al13, with a thickness of about 3 μm. The hybrid joint was stronger despite having a thicker intermetallic layer. This suggests that the morphology and distribution of the intermetallic compounds matter more than their total thickness.

The explanation lies in the heat input distribution. The laser-MIG hybrid process produces a narrower heat-affected zone and a more uniform temperature distribution across the joint. This results in a more uniform intermetallic layer, which is less prone to cracking. The single MIG process produces a wider heat-affected zone and a less uniform temperature distribution, which can lead to localised thickening of the intermetallic layer and the formation of brittle phases.

The tensile strength of 105 MPa is only 33.9% of the aluminium base metal strength. This is a low value, and it reflects the inherent difficulty of joining these two materials. The fracture occurred at the brazing interface and propagated into the weld reinforcement. The failure mode was a mixture of brittle and ductile fracture, with the brittle component dominating at the interface.

Process Windows and Practical Parameters

For dissimilar metal welding between stainless steel and aluminium, the process parameters are even more critical than for similar metal welding. The table below summarises the key parameters and their effects.

Parameter Typical Range Effect on Joint Quality
Laser power 1.5-3 kW Controls the width of the intermetallic layer
MIG current 80-150 A Controls filler metal deposition and wetting
Welding speed 0.5-1.5 m/min Slower speed gives more time for intermetallic growth
Laser-MIG distance 2-4 mm Affects the heat input distribution
Filler wire Al-Si or Al-Mg alloys Si promotes wetting and reduces intermetallic growth
Joint gap 0-0.5 mm Minimal gap is preferred to avoid burn-through

The choice of filler wire is critical. Al-Si filler alloys are commonly used because silicon promotes wetting of the stainless steel surface and reduces the formation of brittle intermetallic compounds. Al-Mg fillers are less suitable because magnesium does not promote wetting as effectively. The filler wire also determines the composition of the brazed joint, which affects its mechanical properties.

The welding process itself is a brazing process rather than a fusion welding process. The laser and the arc heat the aluminium and the filler wire, but the stainless steel is only heated to a temperature below its melting point. The filler metal wets the stainless steel surface and forms a metallurgical bond through the intermetallic layer. This is why the process is called laser-MIG brazing rather than welding.

Defect Analysis and Countermeasures

The most common defects in stainless steel to aluminium brazed joints are lack of wetting, intermetallic cracking and porosity. Lack of wetting occurs when the filler metal does not spread over the stainless steel surface, leaving unwetted areas that provide a path for crack initiation. Intermetallic cracking occurs when the intermetallic layer is too thick or when residual stresses exceed the strength of the brittle compounds.

Defect Root Cause Countermeasure
Lack of wetting Contamination on stainless steel surface Pre-weld cleaning and use of active flux
Intermetallic cracking Excessive intermetallic layer thickness Reduce heat input or increase welding speed
Porosity Hydrogen contamination or gas entrapment Use of dry shielding gas and proper filler wire storage
Undercut Excessive heat input or incorrect torch angle Reduce current or adjust torch angle

The most critical countermeasure is to control the heat input precisely. The intermetallic layer grows by diffusion, and the growth rate increases exponentially with temperature. A small increase in temperature can cause a significant increase in intermetallic thickness. This is why the laser-MIG hybrid process is advantageous: the laser provides precise control of the heat input, and the arc provides the filler metal and the wetting action.

Engineering Practice Cases and Lessons Learned

I have not personally welded stainless steel to aluminium in a production environment, but I have seen the consequences of poor dissimilar metal welding in other material combinations. The most important lesson is that intermetallic compounds are not just a cosmetic issue. They are a structural weakness that can cause catastrophic failure in service.

I recall a case where a client had a stainless steel pipe connected to an aluminium fitting using a brazed joint. The joint failed after about six months of service, and the failure was traced to a thick intermetallic layer that had grown due to the service temperature. The joint had been made with a conventional MIG brazing process, and the intermetallic layer was already thick at the time of manufacture. The service temperature accelerated the growth of the intermetallic layer, and eventually the joint became so brittle that it fractured under normal operating loads.

The lesson from that failure is that dissimilar metal joints must be designed with the service temperature in mind. If the service temperature is high, the intermetallic layer will grow, and the joint will eventually fail. The only way to prevent this is to either keep the intermetallic layer as thin as possible or to use a transition material that is compatible with both metals.

Study Insights and Implications for the Pipe and Fitting Industry

This study provides valuable insights into the relationship between intermetallic layer thickness and joint strength. The finding that a thicker intermetallic layer can produce a stronger joint is counterintuitive, but it makes sense when you consider the morphology of the layer. A uniform intermetallic layer is stronger than a non-uniform one, even if it is thicker.

For the pipe and fitting industry, this has implications for any dissimilar metal joint. Whether it is stainless steel to carbon steel, copper to aluminium, or titanium to steel, the same principles apply. The key is to control the heat input and the intermetallic layer morphology.

The study also highlights the importance of the brazing process in dissimilar metal joining. Brazing is often overlooked in favour of fusion welding, but it is the only viable option for many dissimilar metal combinations. The laser-MIG hybrid brazing process offers a way to combine the precision of a laser with the flexibility of a MIG torch, and it can produce joints with acceptable strength if the parameters are properly controlled.

Reference Value and Outlook

This study is a valuable reference for anyone involved in dissimilar metal welding or brazing. It provides a clear demonstration of the relationship between intermetallic layer thickness and joint strength, and it shows that the morphology of the intermetallic layer is more important than its total thickness.

The outlook for dissimilar metal joining is positive. As the demand for lightweight structures increases, the need for dissimilar metal joints will grow. The laser-MIG hybrid brazing process is a promising approach, but it requires careful control of the process parameters and a thorough understanding of the metallurgy.

The key challenge is to develop a process that can produce a thin, uniform intermetallic layer that is strong enough for structural applications. The current joint efficiency of 33.9% is too low for most structural applications, but it is a starting point. With further development, it may be possible to achieve higher joint efficiencies by optimising the process parameters and the filler wire composition.

In my view, the most important takeaway from this study is that the intermetallic layer is not necessarily a weakness. If it is thin, uniform and well-bonded, it can provide a strong and reliable joint. The challenge is to control the process so that the intermetallic layer has the right morphology, and this requires a thorough understanding of the heat input and the diffusion kinetics.