Thermodynamic Analysis of Interface Reactions in Al-Steel Pulsed Bypass Coupled Arc MIG Brazing
Literature Overview and Process Context
This paper by Shi Yu, Shao Ling, Huang Jiankang, and Gu Yufen from Lanzhou University of Technology, published in Transactions of the Welding Institution (焊接学报), Volume 34, Issue 9, 2013, pages 87-90, addresses one of the most difficult problems in dissimilar metal joining: aluminum to steel. The process is pulsed bypass coupled arc MIG brazing, which is a variant of MIG brazing where a bypass arc is used to control the heat input and the wire melting rate. The filler wire is ER5356, and the substrate is galvanized steel. The authors have done something that is often missing in welding research: they have combined experimental observation with thermodynamic calculation. They used SEM and EDS to identify the intermetallic compounds (IMCs) at the interface, and they used Thermo-Calc software to calculate the Gibbs free energy of Fe2Al5 and FeAl3 at different temperatures. This is a powerful combination, because it explains not just what forms, but why it forms. For anyone who has ever tried to weld aluminum to steel and watched the joint crack or peel, this paper is a valuable reference.
Interface Microstructure and IMC Formation
The authors report that the pulsed bypass coupled arc MIG brazing method can achieve a sound joint between aluminum and iron, and that the interface region contains a layer of Fe2Al5 and FeAl3 intermetallic compounds. This is consistent with what I have seen in aluminum-steel brazing: the IMC layer is thin but brittle, and its thickness and composition determine the joint strength. The authors used ER5356 filler wire, which is an Al-Mg alloy, and the magnesium in the wire can influence the IMC formation. The SEM and EDS analysis showed that the IMC layer is composed of Fe2Al5 and FeAl3, which are the two most common IMCs in the Al-Fe system. Fe2Al5 is the iron-rich phase, and it tends to form as a continuous layer at the interface, while FeAl3 is the aluminum-rich phase, and it tends to form as discrete particles or a thin layer on the aluminum side. The thickness of the IMC layer is critical: if it is too thick, the joint is brittle and fails at low load; if it is too thin, the joint may not have sufficient strength. The authors do not report the IMC thickness, but the thermodynamic analysis provides the basis for understanding its formation.
Thermodynamic Analysis: Why Fe2Al5 Forms First
The thermodynamic calculation using Thermo-Calc is the most valuable part of this paper. The authors calculated the Gibbs free energy of Fe2Al5 and FeAl3 at different temperatures and found that at high temperatures, the Gibbs free energy of Fe2Al5 is lower than that of FeAl3, while at low temperatures, the opposite is true. This means that during welding, when the interface is at a high temperature, Fe2Al5 is thermodynamically favored and forms first. As the joint cools, the temperature drops, and FeAl3 becomes thermodynamically favored, so it forms or precipitates during cooling. This is a classic example of a phase transformation that is controlled by temperature-dependent thermodynamics. The practical implication is that the IMC layer will have a duplex structure: a Fe2Al5 layer that forms at the peak temperature, and a FeAl3 layer that forms during cooling. The relative amounts of the two phases depend on the cooling rate and the peak temperature. A faster cooling rate will suppress the FeAl3 formation, leaving a thinner and more uniform IMC layer, which is generally beneficial for joint strength.
| IMC Phase | Temperature Range | Gibbs Free Energy | Formation Sequence |
|---|---|---|---|
| Fe2Al5 | High temperature (welding) | Lower | Forms first during welding |
| FeAl3 | Low temperature (cooling) | Lower | Forms or precipitates during cooling |
Engineering Practice Implications and Key Lessons
This paper is a valuable contribution to the aluminum-steel joining literature, and it has several practical implications. First, the IMC layer is the weak link in the joint, and its thickness and composition are controlled by the peak temperature and the cooling rate. A lower heat input and a faster cooling rate will produce a thinner IMC layer, which is generally better for joint strength. Second, the thermodynamic analysis explains why the IMC layer has a duplex structure, and this knowledge can be used to design the process. For example, if the peak temperature is reduced, the Fe2Al5 layer will be thinner, and if the cooling rate is increased, the FeAl3 layer will be thinner. Third, the choice of filler wire is important. ER5356 is an Al-Mg alloy, and the magnesium can react with the steel to form other IMCs, which may be more or less brittle than Fe2Al5 and FeAl3. The authors have used a standard filler wire, but a more specialized filler wire could be beneficial. The practical lesson is to control the heat input and the cooling rate to minimize the IMC thickness, and to verify the joint strength with shear testing or peel testing. In my experience, aluminum-steel joints are inherently difficult, and the best results come from a process that minimizes the IMC thickness while ensuring good wetting and fusion. The paper is a solid contribution to the literature, and I would recommend it to any engineer who is joining aluminum to steel for structural applications. The next step would be to investigate the effect of the bypass current and the pulse frequency on the IMC thickness and the joint strength, because the current study does not address those variables in detail.
Zhuojin Pipe Fitting Co., Ltd