ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Microstructure and Mechanical Properties of 6061-T6 Aluminum Alloy DP-MIG Welded Joints Subjected to Post-Weld Rolling

Literature Overview and Core Findings

This study by Song Gang, Dong Xiaonan, Cheng Jiwen, Wang Zeli and Liu Liming from Dalian University of Technology, published in the Transactions of the Welding Institution (2023, Vol. 44, No. 4, pp. 1-6), addresses a persistent problem in welding heat-treatable aluminum alloys: the over-aging softening in the heat-affected zone (HAZ). The authors propose a novel solution: apply synchronous double-sided rolling to the weld joint immediately after welding, using a two-roll system. The idea is to use the weld reinforcement (the excess weld metal) as a source of material that can be deformed to strengthen the over-aged zone. They used 6061-T6 aluminum alloy thin sheet and DC double pulse MIG welding (DP-MIG), then rolled the joint with two rollers positioned on opposite sides of the weld, moving along the weld direction.

The results are impressive. The weld grains undergo large plastic deformation due to the vertical rolling force, internal porosity disappears, and the weld zone becomes wider. The HAZ adjacent to the weld experiences compressive force from the weld metal, causing cooperative macro-deformation. The over-aged softening zone further from the weld receives compressive stress from the weld, resulting in partial cooperative deformation strengthening. The hardness of the over-aged zone increases from 60-70 HV to 80-90 HV. The tensile strength of the joint improves significantly: at a welding speed of 800 mm/min, the ultimate tensile strength reaches 83.6% of the base metal, which is a 19.4% improvement over the as-welded joint. This is a significant achievement for a process that is industrially feasible.

Technical Points and Process Interpretation

The Problem: HAZ Softening in 6061-T6

6061-T6 is a precipitation-hardened aluminum alloy. The T6 temper involves solution treatment, quenching, and artificial aging to form Mg2Si precipitates. During welding, the HAZ experiences temperatures between 200°C and 350°C, which causes over-aging: the fine precipitates coarsen and the strength drops. The HAZ softening zone typically has a hardness of 50-70 HV compared to the base metal hardness of 95-110 HV. The joint efficiency is usually 60-70% for MIG welding. This is a well-known problem, and conventional solutions include post-weld heat treatment (which is impractical for large structures) or using a lower heat input (which reduces penetration).

The Proposed Solution: Weld Rolling

The authors' approach is elegant. The weld reinforcement (the excess weld metal above the plate surface) is not waste; it is a reservoir of material that can be plastically deformed. By applying a rolling force perpendicular to the weld, the reinforcement is pressed down, and the material flows laterally into the HAZ. This causes plastic deformation in the weld and the adjacent HAZ, which:

The process is similar to "weld rolling" or "post-weld rolling" used for reducing residual stress in steel welds, but here it is applied to aluminum with a different objective: to strengthen the softened zone.

Key Parameters and Results

Parameter Value / Range Effect
Welding speed 600-1000 mm/min Higher speed reduces heat input and HAZ width, but also reduces weld reinforcement.
Rolling force Not specified in abstract, but likely 5-20 kN Higher force increases deformation and strengthening, but may cause excessive thinning or cracking.
Roller diameter Probably 50-100 mm Smaller diameter gives higher local pressure.
Roller speed Matched to welding speed Synchronization is critical to avoid tearing.
Weld reinforcement height 1-2 mm above plate surface Provides material for deformation.

The authors report that at 800 mm/min, the tensile strength reaches 83.6% of base metal, which is a 19.4% improvement over the as-welded joint. This means the as-welded joint had a strength of about 70% of base metal (typical for 6061-T6 MIG). The rolling brought it up to 83.6%. The hardness of the over-aged zone increased from 60-70 HV to 80-90 HV, which is a significant improvement.

Microstructural Changes

The paper describes:

This indicates that the rolling force is transmitted through the weld metal to the HAZ, causing plastic strain even in the softened zone. The strain hardening is sufficient to raise the hardness by 20-30 HV.

Integration with Manufacturing Practice

What the Shop Floor Cares About

The automotive and aerospace industries use 6061-T6 aluminum extensively. Welded joints are often the weak link. If a simple rolling operation can improve joint efficiency from 70% to 84%, that is a significant gain. The process is also relatively easy to implement: you need a pair of rollers mounted on a carriage that follows the welding torch. The rollers must be synchronized with the welding speed and positioned to apply the correct force. The main challenges are:

A Case from the Field

I have not personally used this process, but I have seen similar "weld rolling" used for stress relief in steel pipelines. The concept is sound. For aluminum, the risk is that the material is soft and the rollers may cause indentation or buckling if the sheet is thin. The authors used thin sheet (probably 2-3 mm), so the rolling force must be carefully controlled. In a production environment, you would need a closed-loop force control system to maintain consistent pressure. The rollers should be made of hardened steel or polyurethane to avoid marking the aluminum surface.

Defect and Countermeasure Notes

Defect Likely Cause in Weld Rolling Countermeasure
Cracking in weld or HAZ Excessive rolling force; low ductility at rolling temperature. Reduce force; increase welding speed to keep joint hot; use multiple passes with lower force.
Indentation on surface Roller diameter too small; force too high. Increase roller diameter; reduce force; use a compliant roller surface.
Buckling of thin sheet Rolling force applied to unsupported area. Use a backing bar or support rolls on the opposite side.
Inconsistent strengthening Roller misalignment; variation in weld reinforcement. Use a guide system to align rollers; ensure consistent welding parameters.

Key Questions and Reflections

The paper is innovative, but there are several questions that need to be addressed before industrial adoption:

  1. What is the effect of rolling on fatigue strength? The paper only reports tensile strength. Fatigue is often the critical design criterion for aluminum structures. Rolling introduces compressive residual stress, which should improve fatigue, but the surface deformation may create stress concentrations.
  2. How does the process work for thicker sections? The authors used thin sheet. For thicker plates, the rolling force would need to be much higher, and the reinforcement may not be sufficient to provide the necessary deformation. The concept may be limited to thin sections.
  3. What is the effect on corrosion resistance? Rolling may break the oxide layer and expose fresh aluminum, which could affect corrosion behavior. This needs to be tested.
  4. Is the process economically viable? The rolling equipment adds capital cost and requires precise control. For high-volume production, the improvement in joint efficiency may allow weight reduction, which could offset the cost. For low-volume, it may not be worth it.

Study Insights and Implications

This paper presents a novel and practical solution to a long-standing problem. The concept of using the weld reinforcement as a "material reservoir" for deformation strengthening is elegant and industrially feasible. The results show a 19.4% improvement in tensile strength, which is significant. The process could be particularly valuable in automotive and aerospace applications where 6061-T6 is used and where post-weld heat treatment is not practical.

For engineers considering this process, I would recommend the following:

  1. Validate the process on your specific joint geometry and material thickness.
  2. Measure the hardness profile across the joint to confirm the strengthening effect.
  3. Perform fatigue testing to ensure the rolling does not degrade fatigue life.
  4. Optimize the rolling force and speed using a design of experiments approach.
  5. Consider the effect on dimensional accuracy, as rolling may cause slight thinning of the weld reinforcement.

In summary, this paper is a significant contribution to aluminum welding technology. It offers a new way to overcome HAZ softening without expensive heat treatment. The process is simple, robust, and could be integrated into existing robotic welding cells. I would recommend it to anyone working with heat-treatable aluminum alloys and looking to improve weld joint performance.