ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Effect of Cryogenic Treatment Temperature on the Microstructure and Properties of Magnesium Alloy MIG Welded Joints

Why Magnesium Welding Is a Different Beast

The paper by Yang Dong and colleagues from Shanxi Datong University and Taiyuan University of Science and Technology addresses a problem that is well known to anyone who has welded magnesium alloys: the softening of the welded joint. Magnesium alloys have a high thermal expansion coefficient and a low melting point, which makes them susceptible to grain growth and over-aging in the heat-affected zone. The authors propose cryogenic treatment as a method to improve the mechanical properties of the welded joint, and they have investigated the effect of treatment temperature on the microstructure and properties.

Key Technical Points from the Paper

The authors welded a magnesium alloy using MIG welding and then subjected the welded joints to cryogenic treatment at different temperatures. The treatment temperatures were not specified in the abstract, but the results showed that treatment at -190°C for 12 hours produced the best combination of properties. The table below summarises the improvements compared with the untreated joint.

Property Untreated Joint Cryogenic Treated Joint (-190°C, 12 h) Improvement
Hardness Baseline +48.83% Significant
Tensile Strength Baseline +8.02% Moderate
Elongation Baseline +1.25% Small

The microstructural analysis revealed that the cryogenic treatment caused several changes: the number of dimples in the fracture surface increased, the grain size decreased, the amount of second-phase particles increased, and the diffraction peak intensities of the various phases increased. These changes are consistent with the observed improvements in mechanical properties.

The mechanism proposed by the authors is that cryogenic treatment promotes the precipitation of second-phase particles, which strengthens the material. The decrease in grain size is also beneficial because it increases the strength according to the Hall-Petch relationship. The increase in dimple density suggests that the fracture mode becomes more ductile, which is consistent with the slight increase in elongation.

Engineering Practice Implications

Cryogenic treatment is not a common process in the pipe and fitting industry, but it has been used for tooling and for some aerospace components. The authors' results suggest that it could be used to improve the mechanical properties of magnesium alloy welded joints, which would be valuable in applications where weight is critical and the welded joint is the weak link.

However, I would caution against over-interpreting these results. The improvements in tensile strength and elongation are modest, and the cost of cryogenic treatment must be weighed against the benefits. In a production environment, cryogenic treatment adds a significant step to the manufacturing process, and the cycle time and cost may not be justified unless the application demands it.

Another practical consideration is the effect of cryogenic treatment on residual stress. Welded joints contain residual stresses, and cryogenic treatment can redistribute these stresses, which may be beneficial or detrimental depending on the application. The authors have not addressed this, but it is a critical factor in welded structures.

Lessons Learned and Reflections

The paper demonstrates that cryogenic treatment can improve the properties of magnesium alloy welded joints, but the improvements are not dramatic. The hardness improvement of nearly 49% is significant, but the tensile strength improvement of only 8% suggests that the strengthening mechanism is primarily related to the hardness rather than the bulk strength. This is an interesting observation that deserves further investigation.

One area where cryogenic treatment could be more valuable is in the treatment of welded joints in magnesium alloys that are used in high-temperature applications. The second-phase particles that precipitate during cryogenic treatment may improve the high-temperature strength, although this has not been investigated.

In conclusion, this paper provides useful data on the effect of cryogenic treatment on magnesium alloy welded joints. The results are promising but not conclusive, and further work is needed to understand the mechanisms and to optimise the treatment parameters. I would recommend this paper to anyone working with magnesium alloys, but I would not recommend cryogenic treatment as a standard production process without a thorough cost-benefit analysis.