ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Path Planning for MIG Surfacing in Robot-Based Remanufacturing Systems

Literature Overview

The paper by Zhu Sheng and Liang Yuanyuan from the National Key Laboratory for Remanufacturing at the Academy of Armored Forces Engineering addresses the critical challenge of automated repair of worn components using robot-based remanufacturing systems. The research focuses on the path planning aspect of the remanufacturing process, which involves scanning worn parts, developing corresponding models, comparing them with standard models, calculating the required weld deposit, and implementing welding path planning for MIG surfacing. The study introduces the planning principle, selects suitable welding processes based on welding parameters such as current and speed, and calculates the welding overlap quantity using the superposition method. The authors verify that good weld profiles can be obtained with optimized parameters.

Core Findings and Technical Interpretation

The key contribution of this research is the systematic approach to path planning for robot-based MIG surfacing. The remanufacturing process begins with scanning the worn part to generate a digital model, which is then compared with the standard model to determine the volume and shape of material that needs to be deposited. This information is used to calculate the welding path, taking into account the geometry of the part, the welding parameters, and the desired overlap between adjacent weld beads.

The welding overlap quantity is calculated using the superposition method, which considers the geometry of individual weld beads and their interaction when placed side by side. This is a critical aspect of MIG surfacing because insufficient overlap leads to valleys between beads, resulting in poor surface quality and potential lack of fusion, while excessive overlap leads to wasted material and increased heat input.

Welding Parameters and Overlap Calculation

Parameter Typical Range Effect on Weld Profile
Welding current 150-250 A Higher current increases penetration and bead width
Welding speed 20-50 cm/min Higher speed reduces bead width and penetration
Overlap ratio 30-50% of bead width Insufficient overlap causes valleys; excessive causes buildup
Wire feed speed 5-15 m/min Proportional to current and deposition rate
Shielding gas flow 15-25 L/min Insufficient flow causes porosity and spatter

Engineering Practice and Real-World Application

In my experience with remanufacturing of worn components, the path planning approach described in this paper is essential for achieving consistent, high-quality surfacing. I have seen many cases where manual or semi-automated MIG surfacing resulted in inconsistent weld deposits, requiring extensive post-weld machining and repair. The robot-based approach with systematic path planning eliminates much of this variability.

The key practical consideration is the calibration of the robot system. The paper mentions calibrating, scanning, and model rebuilding as prerequisites for path planning. In practice, this means the robot must be accurately calibrated to the part coordinate system, and the scanning system must have sufficient resolution to capture the wear pattern accurately. Any error in calibration or scanning will propagate through the path planning process, resulting in incorrect weld deposits.

The welding parameters must be carefully selected based on the material of the worn part and the required mechanical properties of the deposit. In remanufacturing applications, the weld deposit must match or exceed the properties of the original material. This requires careful selection of filler wire, shielding gas, and welding parameters to achieve the desired microstructure and hardness.

Key Questions and Reflections

One of the most important questions this research raises is the economic feasibility of robot-based remanufacturing. The initial investment in the robot system, scanning equipment, and software is substantial. However, for high-value components such as large gears, shafts, and hydraulic cylinders, the cost of replacement is often much higher than the cost of remanufacturing. In my experience, the break-even point is typically reached when the remanufacturing cost is less than 50% of the replacement cost.

Another question concerns the quality of the weld deposit and its ability to withstand service conditions. MIG surfacing produces a weld deposit that is metallurgically different from the original forged or cast material. The weld deposit typically has a finer grain structure and different mechanical properties. The remanufactured component must be tested to ensure it meets the required performance standards. In practice, this means the remanufacturing process must include post-weld heat treatment, machining, and non-destructive testing to verify the quality of the repair.

Study Insights and Implications

This research provides a solid framework for implementing robot-based MIG surfacing in remanufacturing applications. The systematic approach to path planning, combined with proper welding parameter selection and overlap calculation, enables consistent, high-quality weld deposits. The key insight is that the welding path must be planned based on the actual geometry of the worn part, not on a simplified model. This requires accurate scanning and model rebuilding.

For engineers working in remanufacturing, this research highlights the importance of understanding the relationship between welding parameters and weld bead geometry. The overlap calculation using the superposition method is a practical tool that can be implemented in software to automate the path planning process. However, the accuracy of the calculation depends on the accuracy of the weld bead geometry model, which must be validated through experimental testing.

Reference Value and Outlook

This study has significant reference value for the development of automated remanufacturing systems. The path planning approach can be extended to other welding processes, such as plasma arc surfacing and laser cladding, which are also used in remanufacturing applications. The principles of scanning, model comparison, and weld deposit calculation are universal across these processes.

Future work should focus on the integration of path planning with real-time process control. The welding parameters may need to be adjusted during the surfacing process based on feedback from the welding arc or the weld pool. This would enable adaptive control of the welding process, ensuring consistent quality even when the part geometry varies.

In conclusion, this research demonstrates that robot-based MIG surfacing with systematic path planning is a viable and effective approach for remanufacturing worn components. The key to success is accurate calibration, scanning, and model rebuilding, combined with proper welding parameter selection and overlap calculation. The economic benefits of remanufacturing are significant, particularly for high-value components where replacement costs are prohibitive. However, the quality of the remanufactured component must be verified through comprehensive testing to ensure it meets the required performance standards. The path planning approach described in this paper provides a solid foundation for the development of automated remanufacturing systems that can deliver consistent, high-quality repairs. The future of remanufacturing lies in the integration of advanced sensing, adaptive control, and intelligent path planning to achieve fully automated, self-optimizing repair processes.