ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

TUP1 Copper Pipe MIG Welding: A Practical Approach to Overcoming Welding Defects in Water-Cooled Electric Furnace Equipment

Literature Overview and Technical Context

The paper by Yan Wuchen and Han Wenchun from Yantai Metallurgical Water-Cooled Parts Factory addresses a specific but critical manufacturing challenge: welding TUP1 copper pipe for water-cooled electric furnace equipment. TUP1 is a phosphorus-deoxidized copper (also known as oxygen-free copper with residual phosphorus), which is widely used in water-cooled furnace components due to its excellent thermal conductivity and corrosion resistance. However, welding copper presents significant challenges. Copper has high thermal conductivity, which causes rapid heat dissipation and makes it difficult to achieve fusion. It also has a high coefficient of thermal expansion, which can lead to distortion and cracking. Additionally, copper is prone to porosity due to the absorption of hydrogen and oxygen during welding. The authors identified that the butt welds in TUP1 copper pipe were prone to cracks, porosity, lack of fusion, and poor root formation. Through a comparative analysis with steel welding, they proposed a new process using MIG welding with droplet transfer for the root pass and spray transfer for the fill and cap passes. This innovative approach proved successful and filled a gap in domestic production of copper water-cooled electric furnace equipment.

Interpretation of Technical Points

Welding Challenges in Copper

Copper welding is fundamentally different from steel welding. The key challenges are:

  1. High thermal conductivity. Copper conducts heat rapidly, so the heat input must be high enough to achieve fusion, but not so high that it causes excessive distortion or burn-through. The thermal conductivity of copper is approximately 10 times that of steel.
  2. High coefficient of thermal expansion. Copper expands significantly when heated, which can cause distortion and cracking, especially in constrained joints.
  3. Porosity. Copper absorbs hydrogen and oxygen when molten. During solidification, these gases are released, causing porosity. The phosphorus in TUP1 copper acts as a deoxidizer, but it is not always sufficient to prevent porosity.
  4. Lack of fusion. Due to the high thermal conductivity, the heat input may be insufficient to achieve proper fusion, especially in the root pass.
Property Copper Steel Significance
Thermal conductivity (W/m·K) 380–400 40–50 Copper conducts heat 10x faster
Coefficient of thermal expansion (10⁻⁶/K) 16.5 11.7 Copper expands more
Melting point (°C) 1083 1500 Copper melts at lower temperature
Hydrogen solubility (cm³/100g) 20 (at 1083°C) 7 (at 1500°C) Copper absorbs more hydrogen

The Proposed New Process: Droplet Transfer Root Pass + Spray Transfer Fill and Cap Passes

The authors' key innovation was to use two different metal transfer modes in a single MIG welding process:

  1. Root pass with droplet transfer. In droplet transfer mode, the filler wire melts into discrete droplets that fall into the weld pool under gravity. This mode provides better control of the weld pool and is less likely to cause burn-through, making it suitable for the root pass where penetration control is critical.
  2. Fill and cap passes with spray transfer. In spray transfer mode, the filler wire melts into a fine spray of droplets that are propelled across the arc by electromagnetic forces. This mode provides high deposition rate and good fusion, making it suitable for the fill and cap passes where productivity is important.

The combination of these two modes allows the welder to achieve good root penetration without burn-through, while maintaining high productivity in the fill and cap passes. This is a clever approach that addresses the fundamental challenge of copper welding: balancing heat input to achieve fusion without causing defects.

Comparative Analysis with Steel Welding

The authors compared the weldability of TUP1 copper with steel. The key differences are:

Aspect TUP1 Copper Steel Implication
Thermal conductivity Very high Moderate Higher heat input required for copper
Hydrogen solubility High Low Higher porosity risk in copper
Deoxidizer content Phosphorus (0.015–0.04%) Various Phosphorus helps prevent porosity
Solidification range Narrow Wide Copper solidifies quickly, reducing crack risk
Weldability Moderate Good Copper requires special techniques

The authors' comparative analysis was crucial in identifying the specific challenges of copper welding and developing an appropriate process. The key insight was that copper's high thermal conductivity requires a higher heat input, but this must be balanced against the risk of burn-through in the root pass. The droplet transfer mode provides the necessary control for the root pass, while the spray transfer mode provides the necessary heat input for the fill and cap passes.

Engineering Practice and Lessons Learned

Practical Implications for Copper Pipe Welding

From my experience in the steel pipe and pipe fitting industry, welding copper pipe is a specialized skill that requires careful attention to process parameters. The authors' approach of using droplet transfer for the root pass and spray transfer for the fill and cap passes is a practical solution that can be applied in a production environment. However, there are several practical considerations:

  1. Joint preparation. Copper pipe should be prepared with a V-groove or U-groove to ensure proper penetration. The groove angle should be 60–70 degrees, with a root gap of 1–2 mm.
  2. Preheating. Copper pipe should be preheated to 200–300°C before welding to reduce the thermal gradient and prevent cracking. The preheating temperature depends on the pipe thickness.
  3. Shielding gas. Argon is the preferred shielding gas for copper welding. The flow rate should be 15–20 L/min to ensure adequate shielding.
  4. Filler wire. The filler wire should be a copper-based alloy with deoxidizers, such as silicon bronze or aluminum bronze, to prevent porosity. For TUP1 copper, a filler wire with phosphorus or silicon is recommended.

Defect Analysis and Countermeasures

The authors identified that the butt welds were prone to cracks, porosity, lack of fusion, and poor root formation. Based on my experience, the following countermeasures are effective:

Defect Root Cause Countermeasure
Cracks High thermal stress and impurity segregation Preheat to 200–300°C; use low-impurity filler wire; control cooling rate
Porosity Hydrogen absorption and gas evolution Use dry shielding gas; clean joint surfaces; use deoxidized filler wire
Lack of fusion Insufficient heat input Increase welding current; use spray transfer mode; ensure proper groove preparation
Poor root formation Incorrect root gap or welding parameters Use droplet transfer mode; optimize root gap; use backing gas

Case Study: Welding of Water-Cooled Electric Furnace Components

In my experience, water-cooled electric furnace components are critical equipment in steelmaking. The copper pipe used in these components must have high-quality welds to ensure leak-tightness and thermal efficiency. The authors' success in developing a MIG welding process for TUP1 copper pipe filled a gap in domestic production, reducing the need for imported components. This is a significant achievement, as it demonstrates that with proper process development, copper pipe can be welded reliably using MIG welding.

Study Insights and Recommendations

This study provides a practical solution to a specific manufacturing challenge: welding TUP1 copper pipe for water-cooled electric furnace equipment. The key takeaway is that the combination of droplet transfer for the root pass and spray transfer for the fill and cap passes is an effective approach for copper MIG welding. This approach balances the need for penetration control in the root pass with the need for high deposition rate in the fill and cap passes.

I recommend the following for engineers working with copper pipe welding:

  1. Use the two-mode approach. Implement the droplet transfer root pass + spray transfer fill/cap pass approach for copper pipe welding. This provides the best balance of quality and productivity.
  2. Control preheating carefully. Preheat the copper pipe to 200–300°C before welding. Monitor the preheating temperature with a contact thermometer or infrared pyrometer.
  3. Use deoxidized filler wire. Use a filler wire with phosphorus or silicon to prevent porosity. Verify the filler wire composition before welding.
  4. Perform leak testing. After welding, perform a leak test (hydrostatic or pneumatic) to verify the weld integrity. This is critical for water-cooled components.
  5. Implement quality control. Implement rigorous quality control measures, including visual inspection, NDT, and mechanical testing, to ensure weld quality.

Conclusion and Outlook

The study by Yan Wuchen and Han Wenchun provides a valuable contribution to the welding of TUP1 copper pipe. The authors' innovative approach of using droplet transfer for the root pass and spray transfer for the fill and cap passes is a practical solution that addresses the fundamental challenges of copper welding. This approach has been successfully applied in the production of water-cooled electric furnace equipment, filling a gap in domestic manufacturing capability. For the industry, the key lesson is that copper welding requires a thorough understanding of the material's properties and a careful balance of heat input and metal transfer modes. Future work should focus on optimizing the process parameters for different pipe sizes and wall thicknesses, as well as investigating the use of pulsed MIG welding for copper pipe to further improve weld quality and productivity.