ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Partially Melted Zone Microstructure in 6005A-5083 Aluminum MIG Welds: A Detailed Examination

Literature Overview

This study by Xin Kai and colleagues from Northeastern University and CRRC Qingdao Sifang examines a critical but often overlooked aspect of aluminum alloy welding: the partially melted zone (PMZ) microstructure. The authors studied a two-layer, two-pass MIG welded joint between 6005A aluminum alloy extrusion and 5083 aluminum alloy plate. This combination is commonly used in rail transit vehicles, where 6005A extrusions are used for structural members and 5083 plates are used for skin panels. The PMZ is the region adjacent to the fusion line where the base metal is partially melted during welding, and its microstructure has a significant influence on weld joint performance.

PMZ Microstructural Features

The study identified several important microstructural features in the PMZ that are directly related to the original microstructure of the base metal near the groove:

  1. Coarse grain layer on 6005A extrusion - The extrusion process creates a coarse grain layer approximately 1000-3000 micrometers thick on the surface of the groove. This layer is a remnant of the extrusion process and has a significant influence on PMZ behavior.
  2. Grain boundary liquation - The authors observed liquation along grain boundaries in the PMZ, which is a critical defect mechanism that can lead to hot cracking.
  3. Two distinct PMZ regions - The first pass weld (PMZ I) and second pass weld (PMZ II) exhibit different PMZ characteristics due to differences in dilution rate.
PMZ Region Microstructural Feature Liquation Mechanism
PMZ I (First Pass) Continuous coarse grain structure Grain boundary penetration by molten pool metal
PMZ II (Second Pass) Localized coarse grain regions Grain boundary penetration and low-melting eutectic melting
Near-Fusion Zone Fine grain structure Both penetration and eutectic melting
5083 Side Elongated fiber-like structure Liquation along elongated grain boundaries

Grain Boundary Liquation Mechanisms

The authors identified two distinct mechanisms for grain boundary liquation in the PMZ:

  1. Molten pool metal penetration - Liquid metal from the weld pool penetrates along grain boundaries in the base metal. This mechanism is dominant in the coarse grain regions near the fusion line.
  2. Low-melting eutectic melting - Low-melting point eutectic phases present at grain boundaries melt during welding. This mechanism is dominant in fine grain regions farther from the fusion line.

The distinction between these mechanisms is important because they have different implications for weld quality. Molten pool penetration is primarily a function of welding parameters and heat input, while eutectic melting is more dependent on the base metal composition and original microstructure.

Influence of Extrusion Forming

The finding that the extrusion-formed groove surface has a coarse grain layer is particularly significant. This coarse grain layer is a direct result of the extrusion process, and its presence at the groove surface means that the PMZ in this region will have different characteristics than the PMZ in regions with fine grain structure.

This has important practical implications:

  1. Weld quality - The coarse grain layer is more susceptible to grain boundary liquation and hot cracking than fine grain regions.
  2. Process control - The presence of this layer means that welding parameters must be carefully controlled to minimize liquation in this region.
  3. Joint design - The groove geometry and preparation method can influence the extent and characteristics of the coarse grain layer.

Practical Implications for Aluminum Welding

For rail transit vehicle construction, where 6005A extrusions and 5083 plates are commonly welded together, this research provides valuable insights into weld joint quality. The PMZ is a critical region that can be the site of hot cracking, which is a serious defect that can lead to premature failure of the welded structure.

The authors' finding that the first pass weld has lower dilution than the second pass weld is also significant. This means that the PMZ characteristics can vary between passes, and weld quality may not be uniform throughout the joint. This is an important consideration for multi-pass welding, which is common in thick-section aluminum welds.

Conclusion

This study provides a detailed examination of PMZ microstructure in 6005A-5083 aluminum alloy MIG welds, with particular emphasis on grain boundary liquation mechanisms. The finding that the extrusion-formed groove surface has a coarse grain layer that influences PMZ behavior is particularly important for rail transit vehicle construction. The identification of two distinct liquation mechanisms—molten pool penetration and low-melting eutectic melting—provides a framework for understanding and controlling PMZ defects. For production engineers, the key takeaway is that PMZ quality is influenced by both the original base metal microstructure and the welding parameters. This means that joint preparation and welding process control are both critical for achieving high-quality aluminum welds. I would recommend that any facility welding 6005A extrusions to 5083 plates conduct similar examinations of their own weld joints to understand the specific PMZ characteristics of their materials and processes.