ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

TIG Braze Welding of Aluminium/Steel Dissimilar Metal Joints: Microstructure and Interfacial Characteristics

Literature Overview and Industry Context

This paper by Wang Hailin, Huang Huawei, Wang Jinfeng and Zhang Yuanhao from Hubei University of Automotive Technology and Hubei Dongjun Energy Storage Technology, published in Special Casting and Nonferrous Alloys (2026, Vol. 46, No. 6, pp. 866-870), addresses the challenging problem of joining aluminium to steel. The work is supported by the Hubei Provincial Department of Education Scientific Research Programme (B2022370) and the Shiyan Key Laboratory of Advanced Light Alloy Materials.

Aluminium/steel dissimilar metal joints are increasingly important in automotive, energy storage and aerospace applications. The challenge is that aluminium and steel have very different physical and chemical properties:

  1. Different melting points (660°C for aluminium vs. 1538°C for steel)
  2. Different thermal expansion coefficients
  3. Formation of brittle intermetallic compounds (IMCs) at the interface
  4. Poor solid solubility between aluminium and iron

The authors use TIG braze welding with ER4043 filler wire (Al-Si alloy) to join 5A02 aluminium alloy to Q235 steel. The key innovation is the use of a metal powder coating on the steel surface to improve weldability and control IMC formation.

Core Technical Findings and Interpretation

Weld Formation and Defect Analysis

The authors compared two approaches:

  1. Conventional TIG braze welding without metal powder coating
  2. TIG braze welding with pre-placed metal powder coating on the steel surface

The results show a significant difference:

Condition Weld Quality Defects
Without metal powder Poor Intergranular cracks in weld zone
With metal powder Good No cracks, smooth weld surface

The intergranular cracks in the uncoated specimens are caused by the formation of brittle IMCs at the grain boundaries. The metal powder coating improves the wetting and spreading of the filler metal on the steel surface, reducing IMC formation and preventing cracking.

Microstructure of the Weld Zone

The weld zone microstructure consists of:

The Al-Si eutectic is uniformly distributed, which provides good mechanical properties. The aluminium-side heat-affected zone (HAZ) shows grain coarsening due to the thermal cycle of welding.

Interfacial IMC Formation

The interface between aluminium and steel is critical for joint strength. The authors found that:

  1. Al and Fe atoms diffuse across the interface, forming multiple Fe-Al IMC layers.
  2. Near the steel side, the dominant IMC is FeAl.
  3. Near the aluminium side, the dominant IMC is FeAl3.

The presence of these IMCs is inevitable in aluminium/steel joints, but their thickness and distribution determine the joint strength. The metal powder coating helps to control IMC formation by promoting better wetting and reducing the reaction time.

Process Parameter Windows and Practical Considerations

Based on the literature findings and my own experience with dissimilar metal welding, I can provide the following practical guidance:

Parameter Typical Range Notes
Welding current 80-120 A TIG braze welding
Arc voltage 12-16 V
Travel speed 100-200 mm/min
Filler wire ER4043, 1.2 mm diameter Al-Si alloy
Shielding gas Argon, 15-20 L/min
Metal powder Cu, Ni or Zn-based Pre-placed on steel surface
Preheat temperature 100-200°C Reduces thermal shock

The metal powder coating is the key innovation. It improves the wetting of the filler metal on the steel surface and controls IMC formation. The choice of powder composition is critical and should be optimised for the specific aluminium and steel grades.

Integration with Manufacturing Practice

From my experience in the pipe and fitting industry, this technology has significant potential for several applications:

  1. Automotive body structures: Aluminium/steel joints are used in hybrid body structures to reduce weight while maintaining strength.
  2. Energy storage systems: Aluminium/steel joints are used in battery enclosures and cooling systems.
  3. Heat exchanger fabrication: Aluminium/steel joints are used in brazed heat exchangers.
  4. Electrical connections: Aluminium/steel joints are used in electrical busbars and connectors.

Practical considerations:

  1. Joint design: The joint design is critical for aluminium/steel welding. Lap joints are commonly used, but butt joints can be used with careful preparation.
  2. Surface preparation: The steel surface must be clean and free from oxide. The metal powder coating should be applied uniformly.
  3. Heat input control: The heat input must be carefully controlled to minimise IMC formation. Too much heat causes excessive IMC growth; too little heat causes lack of fusion.
  4. Inspection: Aluminium/steel joints require careful inspection, including visual, ultrasonic and shear testing.
  5. Corrosion protection: The joint may require additional corrosion protection, especially in automotive applications where road salt is present.

Key Questions and Reflections

The paper raises several important questions:

  1. What is the optimal metal powder composition? The paper does not specify the exact composition of the metal powder. Different powder compositions may give different results.
  2. What is the maximum joint strength that can be achieved? The paper focuses on microstructure, not mechanical properties. Further research is needed on joint strength and fatigue performance.
  3. How does the joint perform under cyclic loading? Aluminium/steel joints are often subjected to cyclic loading in automotive applications. The fatigue behaviour needs to be studied.
  4. What is the effect of IMC thickness on joint strength? The paper identifies the IMC types but does not quantify the effect of IMC thickness on joint strength.
  5. Can the process be scaled up for production? The metal powder coating process needs to be automated for high-volume production.

Study Insights and Implications

This paper provides valuable insights into the microstructure of TIG braze welded aluminium/steel joints. The key findings are:

  1. The metal powder coating significantly improves weld quality by preventing intergranular cracks.
  2. The weld zone consists of α-Al equiaxed grains with Al-Si eutectic distributed along the grain boundaries.
  3. The interface contains multiple Fe-Al IMC layers, with FeAl near the steel side and FeAl3 near the aluminium side.

4.