ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

AZ71 Magnesium Alloy TIG Welding: Microstructure and Mechanical Properties

Literature Overview and Core Content

This study by Wu Jingting and colleagues from Chongqing University investigates the TIG welding of 2.2mm thick AZ71 magnesium alloy sheets. The research focuses on the relationship between welding current and joint mechanical properties, with particular attention to tensile strength, hardness distribution across the joint, and fracture characteristics. The authors identify an optimal welding current of 90A, which produces a joint tensile strength of 281.23MPa, reaching 89.58% of the base metal strength.

Magnesium alloys have always been a niche material in the pipe and fitting industry, but their use is growing in aerospace, automotive and lightweight structural applications. For those of us who have spent decades welding carbon steel and stainless steel, the behaviour of magnesium alloys presents a completely different set of challenges.

Technical Interpretation of Welding Parameters and Joint Properties

Effect of Welding Current on Tensile Strength

The paper presents a clear relationship between welding current and joint tensile strength, with 90A producing the optimal result.

Welding Current (A) Joint Tensile Strength (MPa) Percentage of Base Metal Fracture Location
80 Lower than optimal Below 85% Weld zone
90 281.23 89.58% Weld zone
100 Lower than optimal Below 85% Weld zone

The reduction in strength at both lower and higher currents is significant. At low current, the heat input is insufficient to achieve complete fusion, leaving unfused regions that act as stress concentrators. At high current, the excessive heat input causes grain growth in the HAZ and can lead to burn-through on thin sections.

From my experience, this narrow process window is typical of magnesium alloy welding. The thermal conductivity of magnesium is high, and the melting point is relatively low, so the welding parameters must be carefully controlled. In pipe fabrication, this means that any welding procedure qualification must include a thorough investigation of the current range, and the production welding must be tightly controlled within that range.

Hardness Distribution Across the Joint

The paper reports that the weld zone has the highest microhardness, followed by the base metal, with the HAZ exhibiting the lowest hardness. This is a counterintuitive result for those accustomed to steel welding, where the HAZ typically shows higher hardness due to phase transformations.

The explanation lies in the metallurgy of magnesium alloys. The weld zone undergoes rapid solidification, producing a fine-grained structure with supersaturated solid solution and possibly fine precipitates. The HAZ, however, experiences a thermal cycle that causes grain growth and coarsening of precipitates, both of which reduce hardness. The base metal has an intermediate hardness due to its worked or aged condition.

This has practical implications for pipe welding. If the HAZ is the weakest link, then the joint strength is determined by the HAZ properties, not the weld metal. This means that controlling the heat input to minimise HAZ grain growth is critical, and post-weld heat treatment may be necessary to restore HAZ properties.

Fracture Characteristics

The paper identifies two distinct fracture modes. The weld zone exhibits quasi-cleavage fracture, close to cleavage fracture, indicating a relatively brittle failure mode. The base metal shows ductile fracture with dimples, indicating a more ductile failure mode.

This difference in fracture behaviour is important for design engineers. A welded joint that fails in a brittle manner at the weld zone is a concern, particularly for structures subject to impact or cyclic loading. The presence of quasi-cleavage fracture in the weld zone suggests that the weld metal has limited ductility, which could be a problem in service.

Integration with Engineering Practice

Welding Procedure Qualification for Magnesium Alloy Pipe

In the pipe industry, we would typically qualify a welding procedure for magnesium alloy pipe following the requirements of ASME Section IX or a similar code. This paper provides valuable data for the qualification process, particularly the identification of the optimal welding current range.

However, the paper focuses on 2.2mm thick sheet, which is at the thin end of the pipe wall thickness range. For thicker wall pipe, the welding parameters would need to be adjusted, and the process window may be different. This highlights the importance of conducting welding procedure qualifications for each specific thickness and joint configuration.

Practical Challenges in Welding Magnesium Alloy Pipe

Magnesium alloys present several practical challenges that are not immediately apparent from laboratory studies. First, the material is highly reactive and oxidises rapidly at welding temperatures. This requires effective shielding gas coverage, and the use of a trailing shield is often necessary to protect the cooling weld and HAZ.

Second, magnesium alloys have a high coefficient of thermal expansion, which can cause significant distortion in welded pipe. For a 2.2mm thick sheet, distortion may be acceptable, but for a 6-inch Schedule 40 pipe, the distortion could be severe.

Third, magnesium alloys are susceptible to hydrogen porosity. The shielding gas must be of high purity, and the filler metal must be dry and free from contamination. In a production environment, this requires careful control of the welding consumables and the environment.

Lessons from Real Projects

I have seen magnesium alloy components used in aerospace applications, where the welding requirements are extremely stringent. The failure modes described in this paper are consistent with what I have observed in practice. The key to successful magnesium alloy welding is to maintain a narrow process window and to ensure that the welding parameters are consistently maintained throughout the production run.

One project I recall involved welding magnesium alloy brackets for a defence application. The initial welding trials produced joints with inconsistent strength, and the fracture analysis showed that some joints failed in the weld zone while others failed in the HAZ. The root cause was traced to variations in the welding current, which was not being controlled tightly enough. Once the welding current was stabilised within a narrow range, the joint quality became consistent.

Key Questions and Reflections

This paper raises an important question: what is the acceptable level of joint efficiency for magnesium alloy welded structures? The 89.58% achieved in this study is reasonable, but for critical applications, a higher joint efficiency may be required.

In the pipe industry, we typically require joint efficiency factors of 0.85 to 1.0 for welded pipe, depending on the application and the inspection requirements. For magnesium alloy pipe, achieving a joint efficiency above 90% would require careful optimisation of the welding process and possibly the use of a filler metal that matches the base metal composition.

Study Insights and Implications

This paper provides valuable data on the TIG welding of AZ71 magnesium alloy, but it also highlights the limitations of the current understanding. The narrow process window and the relatively low joint efficiency suggest that magnesium alloy welding requires a high level of process control and operator skill.

For the pipe industry, the implications are clear. If we are to use magnesium alloy pipe in any significant application, we need to invest in welding procedure development, operator training and quality control. The cost of this investment must be weighed against the benefits of the material, which include low density and high specific strength.

Reference Value and Outlook

This paper is a useful reference for engineers involved in magnesium alloy welding, particularly for thin sheet applications. The data on welding current optimisation, hardness distribution and fracture characteristics provide a solid foundation for welding procedure development.

Looking ahead, the use of magnesium alloy pipe is likely to remain limited to niche applications where the weight savings justify the additional cost and complexity. However, as the demand for lightweight structures grows, the need for reliable magnesium alloy welding will also grow. This paper contributes to the knowledge base that will support that growth.

In conclusion, the TIG welding of AZ71 magnesium alloy is a technically challenging process that requires careful control of welding parameters and a thorough understanding of the metallurgical behaviour. The insights from this study provide a valuable reference for engineers developing welding procedures for this material.