Dissimilar Steel Deep Penetration TIG Welding: Numerical Simulation with Asymmetric Heat Source
Literature Overview and Context
This study by Huang Yifei and colleagues from Tianjin University addresses a problem that is increasingly common in the pipe fabrication industry: the welding of dissimilar steel joints. In this case, the focus is on joining 8 mm thick 316L stainless steel to Q345 low alloy steel using deep penetration TIG welding — a technique that has been developed to achieve single-side welding with double-side forming (i.e., full penetration from one side with a good root pass on the opposite side).
The paper uses ANSYS finite element software to simulate the welding process and evaluate process stability. The key contribution is the development of an asymmetric heat source model that combines a double-ellipsoid heat source for the upper portion and a cylindrical heat source for the lower portion, with independent adjustment of each component. This model is calibrated against actual welding trials and validated by comparing simulated weld profiles with actual weld cross-sections.
Core Technical Findings
The experimental results confirm that deep penetration TIG welding can achieve single-side welding with double-side forming on 8 mm thick dissimilar steel joints under appropriate welding parameters. The resulting weld has good formation and no significant defects. This is a significant finding because dissimilar steel welding is traditionally challenging due to the differences in thermal properties, melting points, and metallurgical behavior between the two materials.
The asymmetric heat source model is the most interesting technical contribution. The upper portion of the heat source is modeled as a double-ellipsoid, which represents the arc heat distribution on the surface and in the upper part of the weld. The lower portion is modeled as a cylinder, representing the deep penetration effect of the keyhole. The two components can be adjusted independently, allowing the model to accurately represent the heat distribution for different welding conditions. The simulation results using this model show good agreement with actual weld profiles, with an average error of less than 8%.
The simulation also reveals an important phenomenon: the temperature on the 316L stainless steel side is lower than on the Q345 side. This is attributed to the higher thermal conductivity of the stainless steel, which conducts heat away more effectively. The narrower back bead width and higher surface tension of the 316L side help to maintain the keyhole balance, ensuring process stability.
Technical Parameter Comparison
| Parameter | 316L Stainless Steel | Q345 Low Alloy Steel |
|---|---|---|
| Thermal conductivity | Higher | Lower |
| Melting point | ~1400°C | ~1500°C |
| Surface tension | Higher | Lower |
| Temperature during welding | Lower | Higher |
| Back bead width | Narrower | Wider |
Integration with Engineering Practice
Dissimilar steel welding is a fact of life in the pipe fabrication industry. In many projects, stainless steel pipe must be welded to carbon steel pipe — either at the interface between different piping systems or at connections to equipment. The traditional approach is to use a transition joint with a nickel-based filler metal, which is expensive and time-consuming. The deep penetration TIG technique described in this paper offers an alternative that could reduce the number of transition joints and simplify the fabrication process.
The practical challenge is that dissimilar steel welding is inherently prone to problems. The differences in thermal expansion between the two materials can lead to residual stresses and distortion. The carbon from the Q345 side can migrate into the 316L side, leading to sensitization and reduced corrosion resistance. And the formation of brittle phases at the interface can compromise mechanical properties. The deep penetration TIG technique, by achieving full penetration in a single pass, reduces the number of thermal cycles and may mitigate some of these problems.
The asymmetric heat source model is particularly valuable for process development. In my experience, welding procedure qualification for dissimilar steel joints is expensive and time-consuming, and the trial-and-error approach is inefficient. A reliable numerical model can reduce the number of trials required and provide insight into the process that is difficult to obtain experimentally.
Key Questions and Reflections
The paper does not address the metallurgical properties of the dissimilar steel joint — it focuses on the thermal and fluid flow behavior. In practice, the mechanical properties and corrosion resistance of the joint are equally important. The formation of chromium carbides at the interface, the carbon migration from the Q345 side, and the residual stress distribution all need to be evaluated before the technique can be qualified for service.
Another question is the applicability of the technique to thicker sections. The paper demonstrates 8 mm thickness, but many pipe applications require thicker walls. Deep penetration TIG has been developed for thicknesses up to about 12 mm, but the process parameters and heat source model would need to be re-validated for each thickness range.
Study Insights and Implications
For the pipe fabrication industry, the deep penetration TIG technique for dissimilar steel welding is a promising development that could simplify fabrication and reduce costs. The asymmetric heat source model provides a valuable tool for process development and optimization.
However, the technique is not a substitute for proper metallurgical evaluation. Before adopting deep penetration TIG for dissimilar steel joints in critical service, the joint must be fully characterized — mechanical properties, corrosion resistance, and microstructure — and the welding procedure must be qualified in accordance with the applicable code or standard. The numerical model can help with process development, but it cannot replace actual welding trials and testing.
I would recommend that shops considering this technique for dissimilar steel pipe welding start with a thorough literature review and a small-scale feasibility study. The technique has clear potential, but it requires careful development and qualification before it can be used in production.
Zhuojin Pipe Fitting Co., Ltd