High-Entropy Alloy Interlayer for Copper/Steel TIG Welding: Microstructure and Properties
Literature Overview and Core Significance
This paper from China University of Petroleum (East China) addresses the challenging problem of welding copper to steel. Copper/steel composite structures are widely used in the oil and gas industry, chemical processing, and power generation due to their ability to combine the excellent thermal and electrical conductivity of copper with the strength and cost-effectiveness of steel. However, the dissimilar materials have significant differences in physical and chemical properties, particularly poor mutual solubility, which leads to liquid phase separation and weld defects.
The authors propose an innovative solution: using a Fe₅Co₃₀Cr₃₀Ni₃₀Cu₅ high-entropy alloy (HEA) as an interlayer material for TIG welding of T2 copper to Q235 steel. The design rationale is based on the concept of solid solution and high-entropy effects, where the HEA is expected to form a single-phase face-centered cubic (FCC) solid solution that can accommodate the differences between copper and steel. The results demonstrate that the HEA interlayer enables reliable joining of T2 copper to Q235 steel, with good weld formation and no porosity or cracks. The weld zone exhibits a single-phase FCC solid solution structure with significant high-entropy characteristics. The average tensile strength of the joint is 225 MPa, reaching 91% of the copper base metal strength, with an average elongation of 44%. The fracture occurs in the heat-affected zone (HAZ) on the copper side, and the fracture surface shows numerous dimples, indicating ductile fracture.
Technical Interpretation and Process Analysis
High-Entropy Alloy Design and Interlayer Selection
The selection of Fe₅Co₃₀Cr₃₀Ni₃₀Cu₅ as the interlayer material is based on the high-entropy alloy concept, where five or more principal elements are combined in near-equiatomic proportions to maximize configurational entropy and stabilize a single-phase solid solution. In this case, the composition is not equiatomic, but it is designed to achieve a single-phase FCC structure with good strength and ductility. The presence of copper in the HEA composition is particularly important, as it promotes compatibility with the copper base metal, while the iron, cobalt, chromium, and nickel provide strength and corrosion resistance.
The high-entropy effect is crucial for suppressing the formation of brittle intermetallic compounds at the copper/steel interface. In conventional copper/steel welding, the poor mutual solubility of copper and iron leads to the formation of brittle phases and liquid phase separation, resulting in weak and defective joints. The HEA interlayer, with its high configurational entropy, promotes the formation of a single-phase solid solution that can accommodate the compositional gradients between copper and steel without forming brittle intermetallics.
Weld Zone Microstructure and Mechanical Properties
The weld zone microstructure is reported to be a single-phase FCC solid solution with significant high-entropy characteristics. This is a favorable outcome, as it indicates that the HEA interlayer has successfully suppressed the formation of brittle intermetallic compounds and liquid phase separation. The weld zone is homogeneous and free of defects, which is essential for reliable joint performance.
The average tensile strength of 225 MPa, reaching 91% of the copper base metal strength, is a significant achievement. The elongation of 44% indicates good ductility, which is important for applications where the joint may be subjected to thermal cycling or mechanical deformation. The fracture occurring in the copper-side HAZ, rather than in the weld zone or at the interface, is the ideal failure mode, as it demonstrates that the weld zone and interface are stronger than the copper base metal.
Process Parameters and Welding Considerations
The authors used TIG welding with the HEA interlayer. The process parameters, including welding current, arc voltage, travel speed, and shielding gas flow rate, must be carefully controlled to ensure proper melting and mixing of the HEA interlayer with both the copper and steel base metals. The interlayer is likely in the form of a thin foil or wire, which is placed in the joint gap before welding. The TIG arc melts the interlayer and the adjacent base metal, creating a weld pool that solidifies into a single-phase FCC solid solution.
The key process consideration is ensuring that the HEA interlayer is fully melted and mixed with the base metals. If the interlayer is too thin, it may not provide sufficient material to fill the joint gap. If it is too thick, it may not be fully melted, leaving unmelted particles that could act as stress concentrators. The heat input must be sufficient to melt the interlayer and the base metal surfaces, but not so high that it causes excessive dilution or burning of the copper base metal.
Integration with Engineering Practice and Shop Floor Considerations
Practical Applications and Limitations
Copper/steel composite structures are used in a wide range of applications, including transition joints for piping systems, busbars for electrical power distribution, heat exchanger tubesheets, and corrosion-resistant linings for chemical vessels. The ability to weld copper to steel reliably is of significant practical value, as it eliminates the need for mechanical joints or brazing, which are often less reliable and more expensive.
However, the use of a high-entropy alloy interlayer is a relatively new and specialized approach. The HEA material itself is not commercially available in large quantities, and it may be expensive to produce. The welding process requires careful control to ensure proper melting and mixing of the interlayer, and the process window is likely narrower than for conventional welding. For production applications, the cost and availability of the HEA interlayer must be carefully evaluated against the benefits of improved joint quality and reliability.
Quality Control and Verification Strategy
For copper/steel joints with HEA interlayers, the following verification strategy is recommended:
| Verification Level | Method | Acceptance Criteria | Frequency |
|---|---|---|---|
| Process qualification | Weld procedure qualification (WPQ) with metallographic examination | Single-phase FCC structure, no cracks or porosity | Once per material/geometry combination |
| First article inspection | Visual, dimensional, and ultrasonic examination | Full fusion, no disbonding, dimensional accuracy | First production unit |
| In-process monitoring | Arc voltage, current, travel speed, shielding gas flow | Within established process window | Continuous |
| Periodic verification | Tensile testing of representative coupons | Tensile strength ≥ 200 MPa, fracture in copper HAZ | Every 10th component |
| Final inspection | Ultrasonic or radiographic examination | No detectable defects | 100% |
Lessons Learned and Reflections
This paper demonstrates the power of materials design in solving challenging welding problems. The high-entropy alloy concept, which was initially developed for structural applications, has been successfully applied as an interlayer material for dissimilar metal welding. This is a testament to the versatility of the high-entropy alloy concept and its potential for solving practical engineering problems.
The key lesson is that the interlayer material must be designed to be compatible with both base metals. The Fe₅Co₃₀Cr₃₀Ni₃₀Cu₅ composition was specifically designed to include copper, which promotes compatibility with the copper base metal, while the iron, cobalt, chromium, and nickel provide strength and corrosion resistance. This design approach could be extended to other dissimilar metal systems, such as aluminum/steel, titanium/steel, or nickel/steel.
Summary and Outlook
The use of a Fe₅Co₃₀Cr₃₀Ni₃₀Cu₅ high-entropy alloy interlayer for TIG welding of T2 copper to Q235 steel represents a significant advancement in dissimilar metal joining. The HEA interlayer successfully suppresses the formation of brittle intermetallic compounds and liquid phase separation, resulting in a single-phase FCC solid solution weld zone with good mechanical properties. The average tensile strength of 225 MPa, reaching 91% of the copper base metal strength, and the elongation of 44%, demonstrate that the joint is both strong and ductile. The fracture occurring in the copper-side HAZ, with a dimpled fracture surface, confirms that the weld zone and interface are not the weak links. For practical application, the cost and availability of the HEA interlayer must be carefully evaluated, and the welding process must be controlled to ensure proper melting and mixing. Future work should focus on optimizing the HEA composition for specific base metal combinations, evaluating the corrosion resistance of the joints, and scaling the process for production applications. The key takeaway for fellow engineers is that materials design, specifically the high-entropy alloy concept, offers a powerful tool for solving challenging dissimilar metal welding problems.
Zhuojin Pipe Fitting Co., Ltd