ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

TIG Welding of Inconel 625 Alloy: Microstructure and Mechanical Properties Assessment

1. Literature Overview and Context

The paper by Wang Zeming et al. from the Nuclear Power Institute of China examines the TIG welding of 6 mm thick Inconel 625 alloy plates. Inconel 625 is a nickel-based superalloy widely used in nuclear, aerospace, and chemical processing industries due to its excellent corrosion resistance and high-temperature strength. The study focuses on the microstructure and mechanical properties of the welded joint, which are critical for ensuring the integrity of components in service. This is a straightforward but essential study, as the weldability of Inconel 625 is generally good, but the properties of the weld metal and HAZ can vary significantly depending on the heat input and cooling rate.

2. Welding Process and Parameters

The authors used TIG welding with varying parameters. The material is 6 mm thick, which is a common thickness for plate and pipe applications. The welding parameters are not given in detail in the abstract, but the key point is that they were varied to study their effect on the joint.

Parameter Typical Range for 6 mm Inconel 625 Effect
Welding Current 100-150 A Determines heat input and penetration.
Arc Voltage 10-15 V Affects arc length and heat distribution.
Welding Speed 100-200 mm/min Determines heat input per unit length.
Shielding Gas (Ar) 10-15 L/min Protects the weld pool from oxidation.
Filler Wire ERNiCrMo-3 Matches the base metal composition.

The heat input is the critical parameter. Too low and you get lack of fusion; too high and you get excessive grain growth in the HAZ and increased distortion.

3. Microstructural Analysis

The weld metal shows a typical cast structure with a small amount of equiaxed grains in the center, surrounded by columnar grains. This is the classic solidification structure for a nickel-based alloy. The columnar grains grow from the fusion line towards the weld center, following the direction of the maximum thermal gradient. The presence of equiaxed grains in the center is a result of the lower thermal gradient at the center of the weld pool, which allows for nucleation and growth of new grains. The HAZ did not show significant grain coarsening, which is a positive finding. In many nickel-based alloys, the HAZ can be susceptible to grain growth, which can lead to a loss of ductility and toughness. The absence of this phenomenon in this study suggests that the heat input was well-controlled.

Region Microstructure Remarks
Weld Center Equiaxed grains Formed due to lower thermal gradient.
Weld Edge Columnar grains Grow from fusion line towards center.
HAZ No significant grain coarsening Indicates controlled heat input.
Base Metal Fine-grained austenitic structure Typical for wrought Inconel 625.

4. Mechanical Properties

The tensile strength of the welded joint was found to be comparable to the base metal. This is an excellent result, as it indicates that the weld metal has sufficient strength to carry the load. The joint efficiency is essentially 100%. However, the paper does not report on ductility or impact toughness. For a critical application, we would need to know the elongation and the Charpy impact energy. In my experience, the weld metal in nickel-based alloys often has lower ductility than the base metal due to the cast structure and the presence of micro-segregation. The fact that the strength is comparable is a good sign, but we should not assume that the toughness is also comparable.

5. Practical Considerations for Ni-Based Alloys

From a practical standpoint, TIG welding of Inconel 625 is a well-established process. The key challenges are controlling the heat input to minimize distortion and preventing contamination. Nickel-based alloys are very sensitive to contamination from oil, grease, and even the carbon from a marker pen. The filler wire must be clean and the shielding gas must be high purity argon. The weld pool is also very fluid, which can make it difficult to control in the vertical or overhead position. In a production environment, we often use a backing gas to prevent oxidation of the root pass. The paper does not mention this, but it is a critical step for ensuring a sound weld.

6. Conclusion

This paper is a straightforward and useful study of the TIG welding of Inconel 625. The key finding is that the weld metal has a typical cast structure and the joint strength is comparable to the base metal. The absence of HAZ grain coarsening is a positive indicator of a well-controlled process. For a veteran engineer, the takeaway is that this material can be welded with confidence using standard TIG procedures, provided that the heat input is controlled and the cleanliness requirements are met. However, the study is limited in that it does not provide data on ductility, toughness, or corrosion resistance. Before using this data for a critical application, I would require additional testing, including Charpy impact tests at the minimum design temperature and stress corrosion cracking tests in the relevant environment. The weld is likely to be the weak point in the joint, and we need to know exactly how weak.