ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

304 Stainless Steel Tube TIG Welding: Solidification Behaviour and Thermal-Mechanical Coupling

Literature Overview

Yang Haibo and colleagues from Nanjing Vocational University of Industry Technology, Jiangsu University of Science and Technology, and Jiangsu Maritime Institute published this study in Precision Forming Engineering (2023, Vol. 15, No. 12, pp. 173-181). The work addresses a practical problem that I have faced many times on the shop floor: how to optimise welding parameters for thin-wall stainless steel tubes when direct measurement of residual stress is difficult. The authors used TIG welding on 2 mm thick 304 stainless steel pipe, optimised parameters based on macro and micro examination, and then used a double-ellipsoid heat source with temperature-displacement coupling to simulate the residual stress field. The study is a model of how to combine experimental work with simulation to solve a real production problem.

Core Technical Points

The optimal welding parameters were found to be a current of 150 A and a welding speed of 66 cm/min, which produced a fully penetrated joint with uniform and dense weld beads on both the face and root sides. The key results are summarised below.

Parameter / Feature Result
Welding current 150 A
Welding speed 66 cm/min
Weld centre upper region Equiaxed grains
Weld centre lower region Equiaxed grains, slightly larger than upper
Near fusion line Columnar grains
HAZ hardness 197 HV
Weld metal hardness 162 HV
Fusion line hardness 145 HV (minimum)
Longitudinal residual stress Compression in base metal, transition to tension at weld centre
Transverse residual stress Compression at weld centre, approaching zero toward base metal
Radial stress Small variation

The hardness distribution is U-shaped, with the HAZ harder than the weld metal and the fusion line being the softest point. The simulation showed that longitudinal residual stress transitions from compressive in the base metal to tensile at the weld centre, while transverse stress is compressive at the weld centre and approaches zero away from it. The simulated trends matched the measured data closely.

Process and Standards Analysis

This paper is a textbook example of how to handle a common production issue. In thin-wall pipe welding, the biggest risks are burn-through, lack of fusion, and distortion. The authors correctly identified that a fully penetrated joint with uniform bead appearance is the first acceptance criterion, and they used hardness testing to confirm that the joint has no soft zones that would be susceptible to failure. From a standards perspective, this work aligns with ASME Section IX and ISO 15614-1, which require qualification of welding procedures based on visual, dimensional, and mechanical testing. The use of simulation to predict residual stress is particularly valuable because it allows engineers to assess distortion risk before committing to a production run.

Engineering Practice Integration

In my own experience with thin-wall stainless steel pipe, the problem is rarely the welding itself but the consequences of the welding. I have seen 2 mm stainless steel tubes used in heat exchangers, pharmaceutical lines, and food processing equipment, and the most common failure mode is stress corrosion cracking in the residual stress field. The simulation approach used in this paper is exactly what I would recommend to any fabricator: validate the welding parameters on coupons, then use simulation to predict the residual stress distribution, and finally verify with measurement where possible. The U-shaped hardness profile is also a useful diagnostic tool. If you see a hardness dip at the fusion line, you know that the weld is going to be the weak link, and you should consider post-weld heat treatment or a change in filler metal.

Key Questions and Reflections

  1. Does your welding procedure specification actually define the acceptable hardness range for the fusion line, or do you only check the weld metal and HAZ?
  2. How do you handle residual stress in thin-wall pipe when the code does not require stress relief, but the service environment is corrosive?
  3. Is the double-ellipsoid heat source model accurate enough for your material thickness, or do you need a more sophisticated model?

Study Insights and Implications

The key insight is that simulation is not a replacement for testing but a complement to it. The authors validated their model against measured data, which is the only way to trust a simulation. In my own practice, I always insist that any simulation used for production decisions must be validated against at least one set of measured results. The other important point is that the fusion line is the weakest link in a TIG welded 304 stainless steel joint, and this should be reflected in the acceptance criteria. If your procedure qualification only tests the weld metal, you are missing the most likely failure location.

Reference Value and Outlook

This paper is a valuable reference for anyone welding thin-wall stainless steel pipe, particularly in industries where corrosion resistance and dimensional stability are critical. The combination of parameter optimisation, microstructural analysis, and thermal-mechanical simulation is a template that can be applied to other materials and thicknesses. I would recommend this approach to any fabricator who is struggling with distortion or cracking in thin-wall pipe, and I would add one piece of advice: always measure the residual stress on a production representative coupon before you commit to a full production run.